816267
17
Zoom out
Zoom in
Previous page
1/280
Next page
17
English
TROUBLESHOOTING
WARNING
To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or remove the
battery from the main body before making any adjustments.
All electrical or mechanical repairs should be done only by quali ed service technicians. Contact HiKOKI Authorized
Service Center.
1. Power tool
Problem Possible Cause Remedy
Tool doesn’t run No remaining battery power Charge the battery.
Battery isn’t fully installed. Push the battery in until you hear a click.
Tool suddenly stopped Tool was overburdened Get rid of the problem causing the
overburden.
During operation, lighten the applied
pressure.
Battery or tool overheated Allow the tool and battery to thoroughly cool.
Doesn’t cut well The bit is worn or missing teeth. Replace with a new bit.
The collet chuck is loose. Firmly tighten the collet chuck.
Switch can’t be pulled ON/OFF Lock button is pushed in Release the ON/OFF Lock button.
Battery cannot be installed Attempting to install a battery other than that
speci ed for the tool. Please install a multi volt type battery.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 97 dB (A)
Measured A-weighted sound pressure level: 89 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN62841.
Cutting MDF:
Vibration emission value ah < 2.5 m/s2
Uncertainty K = 1.5 m/s2
The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of
exposure.
WARNING
The vibration and noise emission during actual use
of the power tool can di er from the declared total
value depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
00BookM3612DA.indb1700BookM3612DA.indb17 2023/09/0722:54:232023/09/0722:54:23
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki M3612DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki M3612DA in the language / languages: All languages as an attachment in your email.

The manual is 16.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info