816381
9
Zoom out
Zoom in
Previous page
1/116
Next page
9
English
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a quali ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of
children and in rm persons.
DEMOLITION HAMMER SAFETY
WARNINGS
Safety instructions for all operations
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements speci ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of su cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
5. Before starting to break, chip into a wall, oor or ceiling,
thoroughly con rm that such items as electric cables or
conduits are not buried inside.
6. At the start of work, con rm screw tightening.
7. When working at a highly elevated location, pay attention
to articles and persons below.
8. Wear protective shoes to protect your feet.
9. Wear a dust mask.
Do not inhale the harmful dusts generated in chiseling
operation. The dust can endanger the health of yourself
and bystanders.
10. Mounting the tool
To prevent accidents, make sure to turn the switch o
and disconnect the plug from the receptacle.
When using tools such as bull points, cutters, etc.,
make sure to use the genuine parts designated by our
company.
Clean the shank portion of the bull point. Then smear the
shank portion with the grease or machine oil.
11. The impact rate cannot be changed by pressing the
impact rate selector switch while the motor is rotating.
To change speeds, switch o the tool rst.
12. Be sure to grip the handle and side handle during work.
Do not hold by the grip during work. If you pull it by
mistake, the bull point could jump out.
13. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
14. Make sure to securely hold the tool as shown in Fig.13
during operation.
NAMES OF PARTS (Fig.1–Fig.14)
Tool shank
Front cap
Grip
Grip (B)
ON-Lock switch
Trigger switch
Handle
Impact rate selector switch
Power lamp
Display lamp
Nameplate
Motor (internal)
Tail cover
Housing
Side handle
Grip
Handle holder
Bolt
000BookH45ME.indb9000BookH45ME.indb9 2022/10/3111:25:182022/10/3111:25:18
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki H45MEY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki H45MEY in the language / languages: All languages as an attachment in your email.

The manual is 12.46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info