816221
13
Zoom out
Zoom in
Previous page
1/228
Next page
English
13
Action Figure Page
How to recharge USB device 18 6
When charging of USB device is
completed 19 6
Selecting accessories*3215,
216
*1 When conducting chipping operations or alignment
operations, change the tool’s impact rate in accordance
with the task by using the impact rate selector switch.
NOTE
Impact rate cannot be adjusted until a battery is
installed to the power tool and the switch has been
triggered once.
While the tool’s motor is operating, impact rate cannot
be adjusted by pressing the impact rate selector switch.
To adjust impact rate, switch off the tool.
Once the motor has stopped, press the impact rate
selector switch to adjust the impact rate.
*2 Operate this Demolition Hammer by utilizing its empty
weight. The performance will not be better even if it is
pressed or thrust forcibly against the work surface.
Hold this Demolition Hammer with a force just sufficient
to counteract the reaction.
*3 For detailed information regarding each tool, contact a
HiKOKI authorized service center.
Warming up (Fig.14)
The grease lubrication system in this unit may require
warming up in cold regions.
Position the end of the bit so makes contact with the
concrete, turn on the switch and perform the warming up
operation. Make sure that a hitting sound is produced and
then use the unit.
ABOUT THE PROTECTION
FUNCTIONS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered during
operation, the display lamp will blink as described in
Table3. When any of the safeguard functions are
triggered, immediately remove your finger from the switch
and follow the instructions described under corrective
action.
Table 3
Display lamp
flashing Cause Solution
Flash
Internal
temperature has
risen beyond the
unit’s specified
temperature.
(Temperature
increase
protection
function)
Turn off the unit
and allow it to
cool down for
about 15 to
30minutes.
When the
temperature
goes down,
press the impact
rate selector
switch to
recover.
Display lamp
flashing Cause Solution
Flash
Excessive
pressure applied
to the tool has
resulted in an
overload.
(Overload
protection
function)
Press the impact
rate selector
switch to
recover. Try to
avoid tasks that
will apply excess
pressure to the
unit.
Flash Sensor signal
read error.
(Control
monitoring
function)
Press the impact
rate selector
switch to
recover. Repair
may be required
if this error
continuously
occurs.
GREASE REPLACEMENT
This Demolition Hammer is of full air-tight construction to
protect against dust.
Therefore, this Demolition Hammer can be used without
lubrication for long periods. Replace the grease as
described below.
Grease Replacement Period
After purchase, replace grease after every 6 months of
usage. Ask for grease replacement at the nearest
authorized Service Center.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turn off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the tool
Since use of as dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
2023/07/20 17:28:42Stylesheet: EU Version: 2023.6.21
H3641DA_C99749471_308_EU
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki H3641DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki H3641DA in the language / languages: All languages as an attachment in your email.

The manual is 3.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info