816379
8
Zoom out
Zoom in
Previous page
1/100
Next page
8
English
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
Case .............................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Demolishing concrete, chipping o concrete, grooving, bar
cutting, and driving piles.
Application examples:
Installation of piping and wiring, sanitary facility installation,
machinery installation, water supply and drainage work,
interior jobs, harbor facilities and other civil engineering
works.
SPECIFICATIONS
Voltage (by areas) (110 V, 230 V, 240 V)
Power Input 500 W
Full-load Impact Rate 0–3200 min-1
Weight
(According to EPTA-
Procedure 01/2014) 3.6 kg
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Mounting a tool 22
Dismounting a tool 32
Deciding working position of tool 42
Switch operation 53
How to use the demolition hammer*163
Replacing carbon brushes 73
Selecting accessories*25
*1 By utilizing the empty weight of the machine and
by rmly holding the hammer with both hands, one
can e ectively control the subsequent recoil motion.
Proceed at a moderate work-rate, the use of too much
force will impair e ciency.
*2 For detailed information regarding each tool, contact a
HiKOKI authorized service center.
GREASE REPLACEMENT
This machine is of full air-tight construction to protect against
dust and to prevent lubricant leakage. This machine can be
used without grease supplement for an extended period of
time. However, perform the grease replacement to maintain
the service life. Replace the grease as described below.
1. Grease Replacement Period
You should look at the grease when you change the
carbon brush. (See item 4 in the section MAINTENANCE
AND INSPECTION.) Ask for grease replacement at the
nearest authorized HiKOKI Service Center.
In the case that you are forced to change the grease by
yourself, please follow the following points.
2. How to replace grease
CAUTION
Before replacing the grease, turn the power o and pull
out the plug from the receptacle.
(1) Remove the crank case cover and wipe o the old
grease inside. (Fig. 8)
(2) Supply 25 g (the standard volume to cover the connecting
rod) of HiKOKI Electric Hammer Grease A to the crank
case.
(3) After replacing the grease, install the crank case cover
securely. At this time, do not damage or lose the oil seal.
NOTE
The HiKOKI Electric Hammer Grease A is of the low
viscosity type. When the grease is consumed, purchase
from an authorized HiKOKI Service Center.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
1. Inspecting accessories
Since use of a dull accessory, such as a bull point, a
cutter, etc. will degrade e ciency and cause possible
motor malfunction, sharpen or replace with a new one as
soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 7)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or near
the “wear limit” , it results in motor trouble.
When an auto-stop carbon brush is equipped, the motor
will stop automatically. At that time, replace both carbon
brushes with new ones which have the same carbon
brush Numbers shown in the Fig. 7. In addition,
always keep carbon brushes clean and ensure that they
slide freely within the brush holders.
5. Replacing carbon brushes (Fig. 7)
Loosen the set screws and remove the tail cover .
Remove the brush caps and carbon brushes . After
replacing the carbon brushes, do not forget to tighten the
brush caps securely and to install the tail cover.
6. Replacing supply cord
If the replacement of the supply cord is necessary, it
has to be done by HiKOKI Authorized Service Center to
avoid a safety hazard.
000BookH25PV.indb8000BookH25PV.indb8 2022/10/0614:51:492022/10/0614:51:49
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki H25PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki H25PV in the language / languages: All languages as an attachment in your email.

The manual is 7.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info