816410
3
Zoom out
Zoom in
Previous page
1/28
Next page
3
ENGLISH en
2.4 Extending guide rail
See page 2, g. D.
Using the connector (order no. 4100080) two guide rails
can be joined.
Align the guide rails ush. Push connector into the guide rail.
Tighten the four tappets in clockwise direction using the tool
provided.
2.5 Setting mitre guide
See page 2, g. A.
Undo the knurled screw at the bottom side of the mitre
guide. Insert mitre guide into T-groove (1). Set desired
angle and tighten knurled screws again by hand.
Order no. 4100081
1. SPECIFIED CONDITIONS OF USE
The guide rails permit precise, splinter-free sawing of planks
and boards with the following HiKOKI hand-held circular
saws and HiKOKI plunge-type saws:
C3606DPA
Various circular saws of the following manufacturers
are compatible with this guide rail: Bosch, Festool, Hilti,
Metabo, Makita.
2. CIRCULAR SAWS WITH GUIDE
GROOVE
2.1 Clamping guide rail
See page 2, g. A.
Using the tensioning clamps (711237) and the quick action
clamp (711238), the guide rail can be secured on the
workpiece for safe working and protection from slipping.
The tensioning clamps are pushed onto both sides of the
guide rail into the T-slot (1).
2.2 Attaching the machine
Descriptions for machines with a groove (2) in the circular
saw guide plate:
See page 2, g. B.
- Mount the circular saw as shown on the guide rail. (The
groove (2) in the circular saw guide plate slides in the
pro le (3) of the guide rail)
- Depending on the machine, gliding without play can be
set on the guide rail (see operating instructions of the
machine).
Diagonal cuts can be carried out in all angle settings.
2.3 Splinter Protection, Adhesive Coating and Sliding
Coating
Prior to attaching the Sliding Coating, the adhesive
remains on the guide rail must be removed completely
(if required using solvent)!
See page 2, g. C.
Splinter Protection:
In new condition, the outside edge of the Splinter Protection
(6) protrudes slightly beyond the cutting track of the circular
saw blade. This protruding section is cut o in the rst
cut. To avoid tearing, the Splinter Protection (6) should lie
completely on a support when sawing. The edge of the
Splinter Protection is then cutting edge of the workpiece.
When changing the circular saw, it is usually necessary to
replace the Splinter Protection with a new one. For easier
insertion of the new Splinter Protection (6) the front area can
be pulled out from the guide rail (about 2–3 cm) to permit
a safe grip (see page 2, g. E). If the insertion by hand is
too di cult, pliers can be used to pull the Splinter Protection.
Since the insertion can cause lengthening of the Splinter
Protection, we recommend letting the guide track rest for a
while before cutting o the protruding ends of the Splinter
Protection. Spare Splinter Protections can be ordered under
order no. 4100077.
Adhesive Coating:
Replace the Adhesive Coating (4) in case of damage or
strong wear. Replacements can be ordered under order no.
4100079.
Sliding Coating:
Replace the Sliding Coating (5) in case of damage or
strong wear. Replacements can be ordered under order no.
4100078.
(Original instructions)
0000BookGR800.indb30000BookGR800.indb3 2022/08/0521:51:542022/08/0521:51:54
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki GR800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki GR800 in the language / languages: All languages as an attachment in your email.

The manual is 2.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info