816414

Hikoki GP18DB Manual

10
Zoom out
Zoom in
Previous page
1/240
Next page
10
English
Disconnect the battery
Switching ON
Switching OFF
Warning
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 231.
Standard accessories are subject to change without notice.
APPLICATIONS
○ Finishing of dies for press working, die casting and
moulding.
○ Finishing of thread cutting dies, tools and other small
parts.
○ Internal grinding of tools and machine parts.
SPECIFICATIONS
Model GP18DA GP18DB
Voltage 18 V
Rated speed 7000–29000 min–1
Max. Wheel diameter 50 mm
Collet chuck Capacity* 6 mm
Weight** 2.3 kg (BSL1850C)
2.8 kg (BSL36B18)
* This varies depending on the area.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
Electronic control
○ Soft start
Reduces recoil against the operator by managing the
number of rotations during startup.
○ Overload protection
This protection feature cuts off the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Restart prevention function
When the power is still switched on, the tool will not
restart when a battery is installed. This function can be
canceled once the tool is switched off .
○ Braking Function
Brake is activated when the switch is turned off , stopping
the motor’s rotation.
○ Kickback Protection
The kickback protection feature cuts off the power to
the motor and stops the power tool in the event of a
sudden drop in the rotational speed of the wheel during
operation (for example, if the wheel locks during cutting
operation, etc.).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1- second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3 (on page 2).
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the pilot lamp
will blink in red. (At 1-second intervals) (See Table 1)
● Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
00BookGP18DA.indb1000BookGP18DA.indb10 2021/03/1715:12:132021/03/1715:12:13
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki GP18DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki GP18DB in the language / languages: All languages as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info