816341
16
Zoom out
Zoom in
Previous page
1/288
Next page
16
English
*4 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
NOTE
The wheel washer is speci cally for this product. Do
not use it for any other product.
*5 About the mode change function
With Auto mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
lowered if the load decreases during operation.
NOTE
To enable mode changes, pull the switch once after
installing the battery.
The set mode remains set even if the power is turned o .
Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
<
G3612DVE, G3613DVE, G3613DVF, G3615DVE, G3615DVF>
Pressing the Auto mode switch will change the
operating mode back and forth between Auto mode and
Transmission mode.
With Transmission mode, the grinder’s number of
revolutions can be set at one of six levels using the dial.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
Set the mode and dial according to work application.
(Table 3)
Table 3
Status
Number of
Revolutions (min-1)
Use
G3612DVE
G3613DVE
G3613DVF
G3615DVE
G3615DVF
1 3200 3200 Grinding stainless
steel
239
00
3600
Rust or paint removal
Grinding, nishing
3 5300 4600
4 7400 5600
Rough grinding,
cutting
5 8600 7200
6 10000 8000
Auto L 5500 5500 Light work, Standby
state
Auto H 10000 8000 Grinding, cutting
Auto L: No-load
Auto H: During operation
<G3613DE, G3613DF>
Pressing the Auto mode switch will change the operating
mode back and forth between Auto mode and Full-Speed
mode. In Full-Speed mode, the number of revolutions is
controlled so that it always remains constant.
Set the mode according to work application.
*6 Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
Wipe o any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
*7 Grinding angle and grinding method
Press down the machine evenly on the surface and
move back and forth so that the surface of the workpiece
does not become too hot.
Rough grinding: position the machine at an angle of
15°–30° for the best working results.
When the grinding stone is new, its corner may dig in
when it is pushed forward, so pull back during use.
(Fig. 14-a)
Once the wheel edge is worn, the workpiece can be
ground in both directions. (Fig. 14-b).
*8 Cutting work
Always work against the run of the disc. Otherwise there
is the danger of the machine kicking back from the cut
out of control. Guide the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 4. When any of the safeguard functions are triggered,
immediately remove your nger from the switch and follow
the instructions described under corrective action.
Table 4
Safeguard
Function LED Light Display Corrective
Action
Overburden
Protection On 0.1 second/
o 0.1 second Remove the
cause of the
overburdening.
Kickback
Protection
Temperature
Protection
On 0.5 second/
o 0.5 second
Allow the tool
and battery
to thoroughly
cool.
MAINTENANCE AND INSPECTION
WARNING
Be sure to turned o the switch and remove the battery
before maintenance and inspection.
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
00BookG3612DVEEU.indb1600BookG3612DVEEU.indb16 2022/08/3016:25:462022/08/3016:25:46
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki G3612DVE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki G3612DVE in the language / languages: All languages as an attachment in your email.

The manual is 14.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info