Manual Hikoki G13VE2 (page 8 of 184) (All languages)

816285

Zoom out

Zoom in

1/184

English

– Do not use separate reducing bushings or adapters to

adapt large hole abrasive wheels;

– For tools intended to be ﬁ tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to

accept the spindle length;

– Do not use cutting oﬀ wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite ﬂ ammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, ﬁ rst disconnect the tool from

the mains supply (use non metallic objects) and avoid

damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves, helmet

and apron should be worn;

– Pay attention to the wheel that continues to rotate after

the tool is switched oﬀ .

– When using dual-purpose (combined grinding and cut-oﬀ

wheels), use only the type A wheel guard (See page 176)

– When using a type A wheel guard for lateral grinding,

the guard may interfere with the workpiece causing poor

control.

– When using a type B wheel guard for cutting-oﬀ

operations with bonded cut-oﬀ wheels, there is an

increased risk of exposure to emitted sparks and

particles, as well as exposure to wheel fragments in the

event of a wheel burst.

– When using a type A, B wheel guard for cutting-oﬀ

operations or lateral grinding in concrete or masonry,

there is an increased risk of exposure to dust and loss of

control resulting in kickback.

– Do not use any segmented diamond cut-oﬀ wheels with

segment slits >10 mm. Only negative segment cutting

angles are permitted.

– The workpiece must lay ﬂ at and be secured against

slipping, e.g. using clamps. Large workpieces must be

suﬃ ciently supported.

– Observe the speciﬁ cations of the tool or accessory

manufacturer. Protect wheels from grease or impact.

– Accessories must be stored and handled with care in

accordance with the manufacturer's instructions.

WARNING

– When using a cutting-oﬀ wheel, be sure to attach a type

A wheel guard.

– When using a grinding wheel, be sure to attach a type B

wheel guard.

– For safety reasons, only use the wheel guard provided

for the respective accessory. Using an incorrect wheel

guard can lead to loss of control and serious injuries.

See also page 176.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Ensure that the power switch is in the OFF position. If the

plug is connected to a receptacle while the power switch

is in the ON position, the power tool will start operating

immediately, which could cause a serious accident.

3. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. Ensure that the depressed center wheel to be utilized is

the correct type and free of cracks or surface defects.

Also ensure that the depressed center wheel is properly

mounted and the wheel nut is securely tightened.

5. Conﬁ rm that the push button is disengaged by pushing

push button two or three times before switching the

power tool on.

6. To prolong the life of the machine and ensure a ﬁ rst

class ﬁ nish, it is important that the machine should not

be overloaded by applying too much pressure. In most

applications, the weight of the machine alone is suﬃ cient

for eﬀ ective grinding. Too much pressure will result in

reduced rotational speed, inferior surface ﬁ nish, and

overloading which could reduce the life of the machine.

7. The wheel continues to rotate after the tool is switched

oﬀ .

After switching oﬀ the machine, do not put it down until

the depressed center wheel has come to a complete

stop. Apart from avoiding serious accidents, this

precaution will reduce the amount of dust and swarf

sucked into the machine.

8. When the machine is not use, the power source should

be disconnected.

9. Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident

before the depressed center wheel is assembling and

disassembling.

10. When using the tool at any value except the full speed

(Dial scale 6), the motor cannot be suﬃ ciently cooled

due to the decreased number of revolution. This could

result in the risk of burning and damaging the motor

before an overload protective mechanism starts to

function.

Make sure that you use the tool by lightly applying it

to the surface of material when you use it at any value

except the full speed (Dial scale 6).

11. Caution when using near welding equipment

When using the grinder in the immediate vicinity of

welding equipment, the rotational speed may become

unstable. Do not use the grinder near welding equipment.

12. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

13. Do not operate from a direct current power source,

booster or any other type of transformer. Doing so may

not only cause damage to the grinder, but may lead to

accidents.

14. Some mobile generators may not be usable with the

machine.

NAMES OF PARTS (Fig. 1–Fig. 13,

Page 176)

Motor Filter

Nameplate Dial

Push button Guard clip

(mounted on wheel

guard when packaged)

Side handle Tabs of guard clip

(2 locations)

Gear cover Lever

Depressed center

wheel (sold separately)

Bump of wheel guard

Toolless wheel guard Notch of body

Switch Hole of wheel guard

Housing Bump of lever

Tail cover Wheel washer

00BookG13VE2.indb800BookG13VE2.indb8 2022/12/2716:08:452022/12/2716:08:45

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki G13VE2 in the language / languages: All languages as an attachment in your email.

The manual is 7.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki G13VE2 Manual

Product: