742697
14
Zoom out
Zoom in
Previous page
1/280
Next page
14
English
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 2 2
Charging 3 2
Remaining battery indicator 4 2
Fitting and adjusting the wheel guard 5 2
Fixing the side handle 6 3
Assembling depressed center
wheel*
1
73
Assembling cutting wheel*
1
83
Switch operation 9 4
Adjusting the number of revolution*
2
10 4
Grinding angle and grinding method 11 4
Detaching the lter 12 4
Charging a USB device from a
electrical outlet
13-a 5
Charging a USB device and battery
from a electrical outlet
13-b 5
How to recharge USB device 14 5
When charging of USB device is
completed
15 5
Selecting accessories 274
*1 WARNING
Before use, be sure to tighten the wheel nut with the
included wrench.
Failure to tighten could result in the wheel nut
loosening when the brake is activated during a stop.
NOTE
The wheel washer is speci cally for this product. Do
not use it for any other product.
*2 About the mode change function
The unit has “Transmission mode” and “Auto mode”.
With Transmission mode, the grinder’s number of
revolutions can be set at one of ve stages.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
With Auto mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will
be lowered if the load decreases during operation.
(Table 3,)
Set the mode and dial according to work application.
Table 3
Mode Status Number of Revolutions (min
-1
) Use
Transmission
Dial Settings
1 3000
Grinding stainless steel
Rust or paint removal
Grinding, nishing
2 4750
3 6500
4 8250
Rough grinding, cutting
5 9500
Auto A
5500 Light work, Standby state
9500 Grinding, cutting
000Book_G3613DA_DB_EU.indb 14000Book_G3613DA_DB_EU.indb 14 2019/12/26 11:53:542019/12/26 11:53:54
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki G 3613DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki G 3613DB in the language / languages: All languages as an attachment in your email.

The manual is 9,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info