Manual Hikoki FCJ65V3 (page 9 of 44) (English, German, Dutch, French, Italian, Portuguese, Spanish)

816403

Zoom out

Zoom in

1/44

English

When using the external dust collection equipment,

connect the rubber adapter (accessory of external

dust collection equipment) with end the of hose from

external dust collection equipment.

Then connect the another end of rubber adapter with

the hose attachment part that positioned in rear end of

jig saw. (See Fig. 13)

SELECTION OF BLADES

1. Accessory blades

To ensure maximum operating eﬃ ciency and results it

is very important to select the appropriate blade best

suited to the type and thickness of the material to be cut.

One type of blade is provided as standard accessory.

The blade number is engraved in the vicinity of the

mounting portion of each blade. Select appropriate

blades by referring to Table 1.

2. Acceptable commercial blades (Fig. 14)

This machine is designed to accept most blades

available on the open market. As illustrated in

Fig. 14, blade dimension restrictions are as follows:

○ Thickness : L2 .....Less than 1.6 mm

○ Width : L3 .....6.3 mm

L4 .....8 mm

L5 .....7 mm

NOTE

When cutting thick materials, use HiKOKI genuine blades

which have an inclination as shown in Fig. 4-A or B.

MAINTENANCE AND INSPECTION

1. Inspecting the blade

Continued use of a dull or damaged blade will result in

reduced cutting eﬃ ciency and may cause overloading

of the motor. Replace the blade with a new one as soon

as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must be

returned to HiKOKI Authorized Service Center for the

cord to be replaced.

5. Cleaning

Clean the power tool and hose attachment part by

blowing with dry air from an air gun or other tool. (Fig. 15)

Doing so is eﬀ ective for the emission of chips or other

particles.

6. Servicing

Consult an authorized Service Agent in the event of

power tool failure.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Table 1 List of Appropriate Blades

Material to be cut Material quality Blade No.

Lumber General lumber No.1 or No.31 (thick plate) or No.41 (thick

plate) or No.2 (thin plate)

Plywood No.3 or No.6

Iron plate Mild steel plate No.6

Nonferrous metal Aluminum, copper, brass No.6

Synthetic resin

Phenol resin, melamine resin, etc. No.4 (thick plate) or No.6 (thin plate)

Vinyl chloride, acryl resin, etc. No.2 or No.4 (thick plate) or No.6 (thin

plate)

Foamed styrol, etc. No.2

Pulp

Cardboard, corrugated paper No.2

Hardboard No.5 or No.6

Fiberboard No.6

Others Hard rubber No.2

Slate No.5

000BookFCJ65V3WE.indb9000BookFCJ65V3WE.indb9 2022/02/0215:16:512022/02/0215:16:51

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki FCJ65V3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1.42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki FCJ65V3 Manual

Product: