816420
7
Zoom out
Zoom in
Previous page
1/32
Next page
7
English
APPLICATIONS
Demolishing concrete, chiseling o concrete, grooving, bar
cutting.
Application examples:
Installation of piping and wiring, sanitary facility installation,
machinery installation, water supply and drainage work,
interior jobs, harbor facilities and other civil engineering
works.
SPECIFICATIONS
Voltage (by areas)
(110V, 220V, 230V, 240V)
Power Input 1240 W
Full-load Impact Rate 1400 min-1
Weight
(According to EPTA-
Procedure 01/2014) 15.8 kg
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Mounting a tool *12, 3 2
Switch operation 4 2
How to use the demolition hammer *253
Oil feeding 7 3
Replacing carbon brushes 8 3
Selecting accessories 4
*1 If the tool’s entire notched portion isn’t inserted beyond
the front cover’s end surface, lightly tap the tool using a
hammer or other object to insert it.
*2 Operate this Demolition Hammer by utilizing its empty
weight. The performance will not be better even if it is
pressed or thrust forcibly against the work surface.
Hold this Demolition Hammer with a force just su cient
to counteract the reaction.
CAUTION
Sometimes the tool does not begin the striking motion
even when the motor rotates because the oil has become
thick.
If the tool is used at low temperature or if it is used after a
long time idle, the tool should be used running in for ve
minutes in order to warm it up.
OIL FEEDING
CAUTION
Prior to oil feeding, always disconnect the plug from the
receptacle.
Since an oil chamber is built in this Demolition Hammer, it
can be used for approximately 20 days without replenishing
lubrication oil, assuming that the Hammer is used
continuously 3–4 hours daily.
Feed oil into the oil tank as described below before using this
Demolition Hammer. (See Figs. 6 and 7)
1. Just before no oil is visible in the oil gauge window when
the power tool is held upright, feed oil without fail.
2. Before feeding oil, use the provided wrench to remove
the oil gauge.
Be careful not to lose the rubber packing attached below
the oil gauge.
3. Check the oil level once a day, con rming that oil is lled.
4. After feeding oil, securely clamp the oil gauge.
NOTE
As an optional accessory, oil for the Demolition Hammer
(one liter) is sold separately. Use this oil when oil in the
tank is depleted.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
1. Inspecting accessories
Since use of a dull accessory, such as a bull point, a
cutter, etc. will degrade e ciency and cause possible
motor malfunction, sharpen or replace with a new one as
soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 8)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or near
the “wear limit” , it results in motor trouble.
When an auto-stop carbon brush is equipped, the motor
will stop automatically. At that time, replace both carbon
brushes with new ones which have the same carbon
brush Numbers shown in the Fig. 8. In addition,
always keep carbon brushes clean and ensure that they
slide freely within the brush holders.
5. Replacing carbon brushes
Loosen the screws (Hexagon socket hd. bolt M4×12)
of the cap covers, then remove the cap covers. After
removing the brush caps, the carbon brushes can be
removed.
After replacing the carbon brushes, tighten the brush
caps, then mount the cap covers securely.
6. Replacing supply cord
If the replacement of the supply cord is necessary, it has
to be done by HiKOKI Authorized Service Center to avoid
a safety hazard.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE
found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
000BookH65SC.indb7000BookH65SC.indb7 2022/09/1423:03:562022/09/1423:03:56
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DV18DF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DV18DF in the language / languages: All languages as an attachment in your email.

The manual is 1.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info