816409

Hikoki DUST EXTRACTOR SYSTEM Manual

8
Zoom out
Zoom in
Previous page
1/160
Next page
8
English
2. Adjusting the nozzle position
NOTE
If the nozzle position adjustment button is pressed to
release the lock while the nozzle is in any position other
than fully extended, the nozzle may pop outward.
(1) Press the nozzle position adjustment button and ensure
that the nozzle is in the fully extended position. (Fig. 5)
(2) While holding the tool in a way so that the switch does
not get pressed, place the nozzle against the material to
be drilled. (Fig. 5)
Material
Nozzle
Fully extended
position of nozzle
Nozzle adjustment
button
Place against
material
Fig. 5
(3) While pushing the nozzle adjustment button in the
direction of the arrow, press the tool toward the material,
allowing the nozzle position to shorten until it reaches the
position where the drill bit comes into contact with the
material. (Fig. 6)
Material
While pressing button
Push forward
Drill bit
Fig. 6
NOTE
If the nozzle position is shortened before the nozzle
adjustment button is pressed, the nozzle won’t be locked
in position even if the nozzle adjustment button lock is
released.
(4) Release the nozzle adjustment button to lock the position
of the nozzle. (Fig. 7)
When the nozzle adjustment
button is released
The nozzle becomes locked
Material
Fig. 7
3. Adjust the drilling depth
NOTE
The maximum drilling depth when using the dust
extractor system is 85 mm.
The dust extractor system can be used with drill bits
with diameters of 4.3–20 mm and e ective lengths of
50–100 mm.
If using a drill bit with a diameter of greater than 20 mm,
remove the dust extractor system.
Press the depth adjustment button in the direction of
the arrow to release the lock, move the nozzle to set
the stroke equal to the depth that you want to drill, and
release the depth adjustment button to lock the position.
(Fig. 8)
Release
Depth
adjustment
button While pressing button
Move to set depth of hole
you want to drill
Stroke
(drilling depth)
Material
Fig. 8
00BookDustextractorsystem.indb800BookDustextractorsystem.indb8 2022/10/1111:50:142022/10/1111:50:14
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DUST EXTRACTOR SYSTEM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DUST EXTRACTOR SYSTEM in the language / languages: All languages as an attachment in your email.

The manual is 11.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info