816227
6
Zoom out
Zoom in
Previous page
1/224
Next page
6
English
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger speci ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of re when used with another
battery pack.
b) Use power tools only with speci cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modi ed.
Damaged or modi ed batteries may exhibit
unpredictable behaviour resulting in re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to re or
excessive temperature.
Exposure to re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range speci ed in the instructions.
Charging improperly or at temperatures outside
the speci ed range may damage the battery and
increase the risk of re.
6) Service
a) Have your power tool serviced by a quali ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of
children and in rm persons.
CORDLESS DRIVER DRILL / COMBI
DRILL SAFETY WARNINGS
Safety instructions for all operations
<DV18DE>
a) Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
<DS18DE / DV18DE>
b) Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
Safety instructions when using long drill bits
a) Never operate at higher speed than the maximum
speed rating of the drill bit.
At higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece, resulting
in personal injury.
b) Always start drilling at low speed and with the bit tip
in contact with the workpiece.
At higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece, resulting
in personal injury.
c) Apply pressure only in direct line with the bit and do
not apply excessive pressure.
Bits can bend causing breakage or loss of control,
resulting in personal injury.
ADDITIONAL SAFETY WARNINGS
1. Make sure that the area to be drilled is absolutely free
of any hidden obstructions including electrical wiring,
water, or gas pipes. Drilling into the aforementioned may
result in electric shock or short circuit, gas leak or other
hazards that can cause serious accidents or injuries.
2. Make sure to securely hold the tool during operation.
Failure to do so can result in accidents or injuries (Fig. 2).
3. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
4. Setting up and checking the work environment. Check
if the work environment is suitable by following the
precaution.
5. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
6. When changing the rotational speed with the shift knob,
con rm that the switch is o . Changing the speed while
the motor is rotating will damage the gears.
7. The clutch dial cannot be set between the numerals
"1, 4, 7 … 22" or the dots, and do not use with the clutch
dial numeral between "22" and the line at the middle of
the drill mark. Doing so may cause damage.
8. Always use this unit with clockwise rotation, when using
it as impact drill.
9. Resting the unit after continuous work.
10. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous work
may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically
stopping operation. If this happens, allow the power tool
to cool before resuming use.
11. The motor may stop in the event the tool is overloaded. In
this should occur, release the tool’s switch and eliminate
the cause of the overload.
12. The motor rotation may be locked to cease while the unit
is used as drill. While operating the driver drill, take care
not to lock the motor.
0000BookDS18DE.indb60000BookDS18DE.indb6 2023/08/0817:33:432023/08/0817:33:43
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DS18DE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DS18DE in the language / languages: All languages as an attachment in your email.

The manual is 9.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info