816229
14
Zoom out
Zoom in
Previous page
1/240
Next page
14
English
CAUTION
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o for
0.3 seconds). In such a case, rst let the battery cool,
then start charging.
When the charge indicator lamp ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the
battery 32
Charging 4 2
Installing / Removing the side
handle 53
Tightening torque adjustment 6 3
Selecting the drill position 7 3
Selecting the impact position 8 3
Change rotation speed 9 3
Mounting and removing the hook 10 4
How to use the LED light 11 4
Mounting the bit 12 4
Reversing the rotational direction 13 4
Switch operation 14 4
Remaining battery indicator 15 5
Charging a USB device from a
electrical outlet 17-a 5
Charging a USB device and
battery from a electrical outlet 17-b 5
How to recharge USB device 18 5
When charging of USB device is
completed 19 6
Selecting accessories 230
RFC (Reactive force control)
This product features RFC.
This stops the motor automatically if the tool is jerking
excessively.
The LED light ashes to indicate that RFC has been
activated.
If this occurs, release your nger from the switch before
restarting. (Fig.16)
NOTE
RFC may not always activate under certain working
conditions or situations.
Take care to hold the tool rmly to prevent any jerking
motion.
RFC may also activate if you change position suddenly
while holding the tool.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. If any of the safeguard
functions are triggered during operation, the LED light will
blink as described in Table 5. When any of the safeguard
functions are triggered, immediately remove your nger
from the switch and follow the instructions described under
corrective action.
Table 5
Safeguard
Function LED Light Display Corrective Action
Overburden
Protection
On 0.1 second/o
0.1 second
(rapid blinking)
Blinks for
approximately
3 seconds after the
switch has been
released.
If the operating
with the shift knob
set on “2”, adjust
to “1” and continue
operation.
Remove the
cause of the
overburdening.
RFC
On 0.15 second/o
0.15 second ×
3 times/O
2 seconds
Blinks for
approximately
3 seconds after the
switch has been
released.
Remove the
problem causing
the tool to jerk
excessively.
When operating
the tool, rmly hold
the tool to make
sure it doesn't jerk.
Temperature
Protection
On 0.5 second/
O 0.5 second
(slow blinking)
Blinks while
protection is in e ect.
Allow the tool
and battery to
thoroughly cool.
0000BookDS18DC.indb140000BookDS18DC.indb14 2023/07/1023:48:312023/07/1023:48:31
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DS18DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DS18DC in the language / languages: All languages as an attachment in your email.

The manual is 9.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info