816423

Hikoki DS18DBL2 Manual

9
Zoom out
Zoom in
Previous page
1/268
Next page
9
English
Table 5
Safeguard Function LED Light Display Corrective Action
Overburden Protection
On 0.1 second/off 0.5 second
If the operating with the shift knob set on
HIGH, adjust to LOW and continue operation.
Remove the cause of the overburdening.
Reactive Force Control Remove the cause of the overburdening.
When operating the tool, fi rmly hold the tool to
make sure it doesn’t jerk.
Over-discharge Protection On 0.5 second/off 0.5 second Charge the battery as soon as possible.
Temperature Protection On 0.3 second/off 0.3 second Allow the tool and battery to thoroughly cool.
REACTIVE FORCE CONTROL
This product features a reactive force control (RFC) to
minimize the danger of twisting the operator’s arms when
tool itself suddenly jerks during operation.
When the tool bit is suddenly overburdened, the tool itself
may react to the motor’s force and twist in the opposite
direction of the motor’s rotation, which could result in injury.
(Fig. 18)
When the tool’s built-in control detects a reactive force, it
stops the motor’s output before the entire tool jerks to lessen
the twisting of the operator’s arms.
When this function activates, it will be indicated by the LED
light blinking (0.1-second blinks/off 0.5 seconds) while the
switch is pulled.
(See “LED light warning signals”)
However, as the function may not activate depending on
situations or conditions during operation, so care should
be taken to avoid any sudden overburdening of the tool bit
when operating the tool.
● Possible causes of sudden overburdening
Tool bit biting into material
Impact against nails, metal or other hard objects
Tasks involving prying or any excess application of
pressure, etc.
Also, other causes include any combination of the
aforementioned.
● When the reactive force control (RFC) is triggered
When the RFC is triggered and the motor stops, turn
off the tool’s switch and remove the cause of the
overburdening before continuing operation.
Arms are twisted
Fig. 18
LED LIGHT WARNING SIGNALS
(Fig. 19)
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 5. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
Fig. 19
000BookDS18DBL2.indb9000BookDS18DBL2.indb9 2021/04/1411:35:122021/04/1411:35:12
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DS18DBL2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DS18DBL2 in the language / languages: All languages as an attachment in your email.

The manual is 16.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info