816262
14
Zoom out
Zoom in
Previous page
1/300
Next page
14
English
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o for
0.3 seconds). In such a case, rst let the battery cool,
then start charging.
When the charge indicator lamp ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
Since the built-in micro computer takes about
3 seconds to con rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action Figure Page
Names of parts - Cordless rotary
hammer 12
Names of parts - Dust extractor
system for Rotary hammer*122
Removing and inserting the
battery 33
Charging 43
Remaining battery indicator 53
Installing / Removing the side
handle 63
Inserting SDS-plus drilling tools 74
Removing SDS-plus drilling tools 84
Selecting rotation direction 94
Selecting the operating mode 10 4
Adjusting the drilling depth 11 4
Changing the chisel position 12 4
Removing the quick release chuck
(DH3628DC)*213 5
Inserting the quick release chuck
(DH3628DC) 14 5
Inserting round shank applications
tools (DH3628DC) 15 5
Switch operation 16 5
Setting the speed 17 5
Auto stop function 18 5
LED level function-side view 19-a 6
LED level function-top view 19-b 6
How to use the LED light 20 6
Cleaning of the battery installation
compartment 21 6
Charging a USB device from a
electrical outlet 22-a 7
Charging a USB device and
battery from a electrical outlet 22-b 7
How to recharge USB device 23 7
When charging of USB device is
completed 24 7
Installing the side handle 25 7
Selecting accessories*3288, 289
*1 For details on how to use the Dust extractor system, refer
to the system’s instruction manual.
*2 If it is hard to pull out the drill chuck holder or the drill bit
holder, align the change lever with the mark and turn
the lock grip.
*3 For detailed information regarding each tool, contact a
HiKOKI authorized service center.
0000BookDH3628DA.indb140000BookDH3628DA.indb14 2022/12/0915:14:272022/12/0915:14:27
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki DH3628DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki DH3628DC in the language / languages: All languages as an attachment in your email.

The manual is 17.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info