816206
11
Zoom out
Zoom in
Previous page
1/220
Next page
English
11
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 3 2
Charging 4 2
Installing / Removing the side handle 5 2
Change rotation speed*16 3
How to use the LED light 7 3
Mounting the drill bit 8 3
Removing and mounting the chuck
wrench 9 3
Reversing the rotational direction*210 3
Switch operation 11 3
Remaining battery indicator 12 4
Fixing the body in place (When
rotating forward) 14-a 4
Fixing the body in place (When
rotating in reverse) 14-b 4
Charging a USB device from a
electrical outlet 15-a 4
Charging a USB device and battery
from a electrical outlet 15-b 4
How to recharge USB device 16 4
Selecting accessories 211
*1 Change rotation speed
CAUTION
Before operating the change lever, check and make
sure that the motor has stopped.
A failure can occur if it is operated while the motor is
running.
To operate the change lever, press the push button,
and release the lock of the change lever. Also, check
and make sure after operation that the push button has
returned and that the change lever has been locked.
Switch the change lever without mistake. If it is used at
a position halfway, there is a fear that the service life of
the switching mechanism may be shortened.
*2 Reversing the rotational direction
CAUTION
When the selector switch is in the center position, the
trigger switch cannot be pulled (Fig.10-a). Always set
the selector switch to the center position or remove the
battery pack before performing maintenance, changing
accessories, storing the tool and any time the tool is not
in use.
RFC (Reactive force control)
This product features RFC.
This stops the motor automatically if the tool is jerking
excessively.
The LED light flashes to indicate that RFC has been
activated.
If this occurs, release your finger from the switch before
restarting. (Fig.13)
NOTE
RFC may not always activate under certain working
conditions or situations.
When working, ensure that the material is securely
placed and fastened, hold the tool body securely, and
be sufficiently careful not to suddenly apply a large load
to the tool tip.
Take care to hold the tool firmly to prevent any jerking
motion.
RFC may also activate if you change position suddenly
while holding the tool.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. If any of the safeguard
functions are triggered during operation, the LED light will
blink as described in Table3.
When any of the safeguard functions are triggered,
immediately remove your finger from the switch and follow
the instructions described under corrective action.
Table 3
LED Light Display Safeguard Function
On 0.1second/off
0.5second
Blinks for approx.
3sec after the
switch has been
released.
Overburden Protection
If the operating with the change
lever set on “2”, adjust to “1” and
continue operation. Remove the
cause of the overburdening.
RFC
Remove the problem causing
the tool to jerk excessively.
When operating the tool, firmly
hold the tool to make sure it
doesn't jerk.
On 0.5 second/
Off 0.5second
Blinks while
protection is in
effect.
Temperature protection
Allow the tool and battery to
thoroughly cool.
2023/03/17 15:26:17Stylesheet: EU Version: 2023.2.1
D36DYA_C99746771_303_EU
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki D36DYA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki D36DYA in the language / languages: All languages as an attachment in your email.

The manual is 3.26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info