816290

Hikoki D13VG Manual

5
Zoom out
Zoom in
Previous page
1/124
Next page
5
English
<Capacity with Angle attachment (Optional accessory for D13VF and D13VG)>
Model D13VF D13VG
Speed of angle unit LOW
(650
min–1
)HIGH
(1350
min–1
)LOW
(400
min–1
)HIGH
(900
min–1
)
Capacity
Steel Twist Bit 13 mm 13 mm 13 mm 13 mm
Hole Saw 64 mm 32 mm 70 mm 51 mm
Wood
Flat Spade Bit 40 mm 32 mm 40 mm 40 mm
Auger Bit 38 mm 29 mm 38 mm 32 mm
Hole Saw 114 mm 64 mm 114 mm 102 mm
NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change
without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Fixing and removing side handle
1 113
Fixing and removing side handle and
handle joint 2 113
Mounting and dismounting the bit 3 113
Dismounting the bit (When the drill
chuck cannot be loosened) 4 114
Selecting rotational direction 5 114
Switch operation 6 114
Locking-on the switch 7 114
Releasing the switch 8 114
Dismounting drill chuck from tool 9 114
Mounting angle attachment (Optional
accessory) 10 115
Selecting speed of angle attachment 11 115
Dismounting drill chuck from angle
attachment 12 115
Fixing side handle for angle attachment
13 115
Mounting position of hook (A)*3
(Optional accessory) 14 115
Selecting accessories ―116
*3 Attaching the hook. (Optional accessory)
To attach the hook, it is necessary to disassemble the
handle portion which covered the tool’s electrical system.
For your continued safety and electrical shock protection,
installing the hook on this drill should ONLY be performed
by a HiKOKI AUTHORIZED SERVICE CENTER.
Selecting the appropriate drill bit
○ When boring metal or plastic
Use ordinary metalworking drill bits.
Sizes range from a minimum of 1.2 mm to chuck
maximum capacity.
○ When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
MAINTENANCE AND INSPECTION
1. Inspecting the drill bits
Since use of an abraded drill bits will cause motor
malfunctioning and degraded effi ciency, replace the drill
bits with a new one or resharpening without delay when
abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI Authorized
Service Center.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI power tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the power tool, undismantled, with the GUARANTEE
CERTIFICATE
found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
00BookD10VF.indb500BookD10VF.indb5 2022/12/2711:24:132022/12/2711:24:13
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki D13VG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki D13VG in the language / languages: All languages as an attachment in your email.

The manual is 12.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info