816291
4
Zoom out
Zoom in
Previous page
1/100
Next page
4
English
Lock
Switch locks to the “ON” position.
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
Chuck wrench ........................................................... 1
Side handle ............................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Drilling in metal, lumber and plastics.
SPECIFICATIONS
Voltage*1(110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
Power input*1720 W
No load speed 650 min-1 (Except for EU
countries: 550 min-1)
Capacity Steel 13 mm
Wood 40 mm
Weight (without cord)*23.1 kg
*1 Be sure to check the nameplate on product as it is
subject to change by areas.
*2 According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI’s continuing program of research and
development speci cations herein are subject to change
without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Fixing spade handle 1 90
Fixing side handle 2 90
Mounting and dismounting the bit 3 90
Selecting rotational direction 4 91
Switch operation 5 91
Locking-on the switch 6 91
Rereasing the switch 7 91
Fixing handle joint 8 91
Fixing depth stopper 9 92
Replacing carbon brushes 10 92
Selecting accessories 93
Selecting the appropriate drill bit:
When boring metal or plastic
Use ordinary metalworking drill bits.
Sizes range from a minimum of 1.2 mm to chuck
maximum capacity.
When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
MAINTENANCE AND INSPECTION
1. Inspecting the drill bits
Since use of an abraded drill bits will cause motor
malfunctioning and degraded e ciency, replace the drill
bits with a new one or resharpening without delay when
abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Inspecting the carbon brushes
The motor employs carbon brushes which are
consumable parts.
When the brushes are worn down, motor trouble may
result. When the brushes are worn down to the limit
line , replace the brushes with new ones. Keep the
brushes clean, so that they smoothly slide into the brush
holders.
When replacing the brushes with new ones, be sure to
use a pair of brushes for HiKOKI ELECTRIC DRILL Type
D13 corresponding to the illustrated number . Auto-
stop carbon brushes automatically cut o the electric
circuit, when it is worn down to the wear limit.
This indicates the replacement time of the brush and
prevents damage of the commutator.
4. Replacing carbon brushes
Disassemble the brush caps with a slotted-head
screwdriver. The carbon brushes can then be easily
removed.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI power tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the power tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
000BookD13.indb4000BookD13.indb4 2022/12/2712:26:462022/12/2712:26:46
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki D13 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki D13 in the language / languages: All languages as an attachment in your email.

The manual is 9.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info