816441

Hikoki CS33EDTP Manual

8
Zoom out
Zoom in
Previous page
1/220
Next page
English
8
MAX Max. engine speed Depth gauge setting
MIN Idle engine speed
Side plate fi ling angle
Type of chain
Top plate angle
Max. chain speed File guide angle
Number of teeth of drive sprocket File
Type of guide bar Depth gauge
NOTE: Noise level/vibration levels are calculated as the time-weighted energy total for noise/vibration levels under various
working conditions with the following time distribution:
*
1: 1/3 idle, 1/3 full, 1/3 racing speed.
*
2: 1/2 full, 1/2 racing speed.
WHAT IS WHAT? (Fig. 1)
A: Throttle lever: Device activated by the operatorʼs fi nger,
for controlling the engine speed.
B: Throttle lever lockout: Device that prevents the
accidental operation of the throttle lever until manually
released.
C: Stop switch: Device for allowing the engine to be started
or stopped.
D: Oil tank cap: For closing the oil tank.
E: Recoil starter: Pull handle to start the engine.
F: Front handle: Support handle located at or towards the
front of the engine housing.
G: Fuel tank cap: For closing the fuel tank.
H: Rear handle: Support handle located on the top of the
engine housing.
I: Choke lever: Device for enriching the fuel/air mixture in
the carburetor, to aid starting.
J: Priming pump: Device for supplying extra fuel, to aid
starting.
K: Guide bar: The part that supports and guides the saw
chain.
L: Saw chain: Chain, serving as a cutting tool.
M: Chain brake (Front hand guard): Device for stopping or
locking the chain.
N: Chain catcher: Device for restraining the saw chain.
O: Air fi lter cover: Cover for air fi lter and carburetor.
P: Side case: Protective cover to the guide bar, saw chain,
clutch and sprocket when the chain saw is in use.
Q: Tension adjustment bolt: Device, often acting on the
guide bar, for adjusting the saw chain tension.
R: Muffl er: Reduces engine exhaust noise and directs the
exhaust gases.
S: Anti-vibration spring: Reduce the transmission of
vibrations to the operator’s hands.
T: Anti-vibration rubber: Reduce the transmission of
vibrations to the operator’s hands.
U: Chain bar clamp nut: Secures the side case and the
guide bar.
V: Attachment point: The part for suspending the unit by
using a safety strap, carabineer or rope.
W: Spiked bumper: Device for acting as a pivot when in
contact with a tree or log.
X: Guide bar cover: Device for covering the guide bar and
saw chain when the unit is not being used.
Y: Combi box spanner: The tool for removing or installing a
spark plug and tensioning the saw chain.
Z: Handling instructions: Included with unit. Read before
operation and keep for future reference to learn proper,
safe techniques.
a: Hot surface caution label: Label for caution to hot
surface.
WARNINGS AND SAFETY
INSTRUCTIONS
Pay special attention to statements preceded by the
following words:
WARNING
Indicates a strong possibility of severe personal injury or
loss of life, if instructions are not followed.
CAUTION
Indicates a possibility of personal injury or equipment
damage, if instructions are not followed.
NOTE
Helpful information for correct function and use.
Operator safety
WARNING
This chain saw (CS33EDTP) is designed especially for
tree care and surgery. Only persons trained in tree care
and surgery may use this saw. Observe all literature,
procedures and recommendations from the relevant
professional organization. Failure to do so constitutes a
high accident risk. We recommend always using a rising
platform for sawing in trees. Rappelling techniques are
extremely dangerous and require special training. The
operator must be trained in and familiar with the use of
safety equipment and working and climbing techniques.
Always use the restraining equipment for both the
operator and the saw.
○ Always use the gloves to reduce the eff ects of vibration.
○ Always wear a safety face shield or goggles.
○ Gloves should be used when sharpening chain.
0000BookCS33EDTP.indb80000BookCS33EDTP.indb8 2019/01/249:52:562019/01/249:52:56
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CS33EDTP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CS33EDTP in the language / languages: All languages as an attachment in your email.

The manual is 46.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info