816328

Hikoki CS1825DC Manual

14
Zoom out
Zoom in
Previous page
1/332
Next page
14
English
After the switch is engaged, the saw chain continues
rotating as long as it is pressed down.
When the switch is released, a brake is applied to stop
the saw chain rotation.
WARNING
Do not secure the lock-off lever in the slid position.
If the switch is accidentally engaged, the unit may
unexpectedly start and injury may occur.
*2 Using the hook
WARNING
When using the hook, ensure the unit is securely
suspended to avoid the risk of falling.
If the unit falls, an accident may occur.
INSTALLING (REPLACING) SAW
CHAIN
WARNING
○ To prevent accidents, always switch the unit off , and
remove the battery.
○ Don't use the saw chain or the guide bar other than
those specifi ed in “SPECIFICATIONS”.
CAUTION
Wear thick gloves and be careful to avoid injury with the
saw chain.
NOTE
○ When removing the saw chain, remove sawdust from
the oil spout, oil hole, and guide bar groove.
If sawdust accumulates, this may cause the unit to fail.
○ Use the correct type of saw chain in accordance with
the specifi cations.
If you install the wrong type of guide bar, the saw chain
may come off and injury may occur.
1. Removing the side cover (Fig. 8)
Turn the nut and remove the side cover.
2. Removing the saw chain and guide bar (Fig. 9)
Rotate the tensioning screw in the “-” direction to
introduce a small amount of slack in the saw chain,
then detach from the sprocket. Detach along with the
guide bar in the direction indicated by the arrow.
3. Engaging the new saw chain in the sprocket
(Fig. 10)
Attach the saw chain from the guide bar tip. Make sure
the saw chain is oriented so that the blade faces in the
direction shown in the illustration below the sprocket.
Insert the bolt and chain tensioner boss into the hole in
the guide bar while holding the chain and guide bar tip.
Engage the end of the saw chain to the sprocket and
mount the guide bar to the saw body.
4. Installing the side cover (Fig. 11)
Attach the side cover by inserting the lug into the slot in
the saw body. Make sure the saw chain does not come
loose from the guide bar.
Rotate the nut once to temporarily fi x it.
Remove any dirt around the side cover before
reattaching.
5. Adjusting the saw chain tension (Fig. 12)
○ While lifting the guide bar tip, turn the tensioning screw
to adjust the saw chain tension.
○ Turn the tensioning screw to the "+" to increase the saw
chain tension, and to the "-" to decrease it.
6. Checking the saw chain tension (Fig. 13)
Adjust the saw chain tension so that the gap between
the saw chain drive link and the guide bar is 0.5 to 1 mm
when you lift the saw chain slightly near the center of
the guide bar.
7. Securing the nut (Fig. 14)
When adjustment is complete, lift up the guide bar, and
fully tighten the nut.
WARNING
After adjusting the saw chain tension, ensure the nut is
fully tightened.
If it is loose, injury may occur.
INSPECTION AND PREPARATION
PRIOR TO USE
Prior to use, make the following inspection and preparation.
WARNING
○ To prevent accidents, always perform steps 1 to 3
ensuring the battery is removed from the body.
○ Do not secure the lock-off lever in the slid position.
If the switch is accidentally engaged, the unit may
unexpectedly start and injury may occur.
1. Ensuring the switch is off
○ If you insert the battery without knowing whether the
switch is engaged, the unit may unexpectedly start,
which may result in an accident.
○ When the switch is engaged while the lock-off lever is
in the slid position, the unit switches on, and when the
switch is released, the unit switches off .
2. Checking the saw chain tension
○ If the saw chain tension is incorrect, there is a risk of
damage to the saw chain or guide bar and malfunction.
Referring to steps 5 to 7 “Installing (replacing) saw
chain,” ensure an appropriate tension is set.
○ While the saw chain is still new, it is particularly
stretchy, so periodically check the tension and adjust
as required.
○ Also check the nut is securely tightened.
3. Checking the chain oil
○ This unit is delivered without chain oil inside. Ensure
the oil tank is fi lled with the chain oil provided before
use. (Fig. 15)
○ Periodically check the oil sight glass during work and
replenish oil as required.
○ If the chain oil supplied runs out, use HiKOKI chain oil
sold separately or equivalent chain oil on the market.
○ The chain oil lubricates automatically.
The discharge rate for auto lubrication is factory preset
to the maximum.
To reduce the discharge rate, turn the oil pump adjuster
on the right side of the oil sight glass clockwise.
(Fig. 16)
NOTE
○ The oil tank capacity is about 70 ml.
Make sure no oil leaks or overfl ows from the oil tank
when replenishing the chain oil.
○ We recommend that you stock up with chain oil.
If you continue working without chain oil, the saw chain
may burn through, or the motor may fail.
○ Be careful to avoid dust or other foreign matter from
entering the oil tank.
If dust and other foreign matter enter the oil tank, the
unit may fail.
○ Chain oil left in the tank may leak due to the structure of
this unit. Although this does not indicate a malfunction,
it may soil the storage location, so be careful.
When storing, empty the oil from the oil tank, and place
an item under the main body which can absorb any
leaks.
○ Replenish the oil after every approximately 10 minutes
of operation. (*Varies depending on the cutting usage
conditions)
00BookCS1825DCEU.indb1400BookCS1825DCEU.indb14 2022/12/0117:02:542022/12/0117:02:54
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CS1825DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CS1825DC in the language / languages: All languages as an attachment in your email.

The manual is 18.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info