816425

Hikoki CR18DGL Manual

7
Zoom out
Zoom in
Previous page
1/188
Next page
7
English
Table 5: Selection of blades for other materials
Material to
be cut Material
quality Thickness
(mm) Blade No.
Iron plate Mild steel
plate 2.5 – 10 No. 101, 102,
103, 104, 109,
110, 131
Below 3.5 No. 107, 108
Nonferrous
metal Aluminium,
Copper and
Brass 5 – 20 No. 101, 102,
103, 104, 109,
110, 131, 132
Below 5 No. 107, 108
Synthetic
resin Phenol resin,
Melamine
resin, etc. 10 – 50 No. 101, 102,
103, 104, 131,
132
5 – 30 No. 107, 108,
109, 110
Vinyl chloride,
Acrylic resin,
etc. 10 – 60 No. 101, 102,
103, 104, 131,
132
5 – 30 No. 107, 108,
109, 110
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting effi ciency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
Table 3: HCS blades
Blade
No. Uses Thickness
(mm)
No. 2 For cutting steel pipe less than 30
mm in diameter 2.5 – 6
No. 3 For cutting steel pipe less than 30
mm in diameter Below 3.5
No. 4 For cutting and roughing lumber 50 – 70
No. 5 For cutting and roughing lumber Below 30
No. 8 For cutting vinyl chloride pipe less
than 100 mm in diameter 2.5 – 15
For cutting and roughing lumber Below 50
No. 9 For cutting mild steel pipe less
than 100 mm in diameter when
used with cut off guide 2.5 – 6
No. 95 For cutting stainless pipe less than
100 mm in diameter Below 2.5
No. 96 For cutting stainless pipe less than
30 mm in diameter Below 2.5
Table 4: Bl-METAL blades
Blade
No. Uses Thickness
(mm)
No. 101
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
No. 102
For cutting steel and stainless
pipes less than 100 mm in outer
diameter 2.5 – 6
No. 103
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
No. 104
For cutting steel and stainless
pipes less than 100 mm in outer
diameter 2.5 – 6
No. 107
For cutting steel and stainless
pipes less than 60 mm in outer
diameter Below 3.5
No. 108
For cutting steel and stainless
pipes less than 100 mm in outer
diameter Below 3.5
No. 109
For cutting steel and stainless
pipes less than 60 mm in outer
diameter 2.5 – 6
No. 110
For cutting steel and stainless
pipes less than 100 mm in outer
diameter 2.5 – 6
No. 121
For cutting and roughing lumber 100
No. 131
All purpose 100
No. 132
All purpose 100
0000BookCR18DGL.indb70000BookCR18DGL.indb7 2018/05/1815:08:242018/05/1815:08:24
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CR18DGL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CR18DGL in the language / languages: All languages as an attachment in your email.

The manual is 12.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info