816250
18
Zoom out
Zoom in
Previous page
1/296
Next page
18
English
Pocket cutting 18 7
Angular cutting*219 8
Concerning cutting of stainless steel
plates 20 9
Connecting with cleaner
(sold separately) 21 9
Charging a USB device from an
electrical outlet 22-a 10
Charging a USB device and battery
from an electrical outlet 22-b 10
How to recharge USB device 23 10
When charging of USB device is
completed 24 10
Selecting accessories 290
*1 The tool is equipped with two modes: “Standard Mode”
and “AUTO Mode”.
(1) Standard Mode
You can change the blade operating speed between
800 to 3500 min-1 by adjusting the dial from “1” to “5”.
(2) AUTO Mode
AUTO Mode automatically selects a speed between
1400 and 3500 min-1 to suit the operating load and
maintains that speed until the switch is turned o .
This has the e ect of lowering vibration and noise
prior to and during operation.
Adjust the dial for the mode and speed that best suits
your task conditions and materials.
Blade operating speed
Mode Dial Blade operating speed
Standard Mode 1 – 5 800 – 3500 min-1
AUTO Mode A No load: 1400 min-1
With load: 3500 min-1
With AUTO Mode, the vibration frequency may not reach
3500 min-1 depending on variables such as the type of
work.
*2 Sub base / Angular cutting
NOTE
When the sub base is attached, the blade’s protrusion
from the material being cut will be reduced by 3–5 mm.
When the blade has been moved down to the lowest
point, check to make sure that it is protruding from the
material.
*3 Switch operation
<CJ36DB>
Do not operate the tool while the switch is held.
The tool does not stop even if the other switch is
operated while this switch is held.
*4 How to use the LED light
<CJ36DA>
NOTE
To prevent the battery power consumption, turn o the
LED light frequently. The light goes out automatically
10 seconds after the switch is released.
<CJ36DB>
Pressing the lighting mode switch on the switch panel
switches between SW interlocked mode and Always-OFF
mode.
To prevent the battery power consumption, turn o the LED
light frequently.
Table 3
SW interlocked mode Always-OFF mode
State
Light only SW-ON
(Automatically goes
out approximately
10 seconds after SW-
OFF)
Always OFF
LED LIGHT WARNING SIGNALS
(Fig. 25)
This product features functions that are designed to protect
the tool itself as well as the battery. When any of the
safeguard functions are triggered, any of the LED light will
blink as described in Table 4.
In this case, follow the instructions described under
corrective action.
Fig. 25
Table 4
Safeguard Function LED Light Display Corrective Action
Overload Protection On 0.1 second/o 0.1 second Remove the cause of the overloading.
Temperature Protection On 0.5 second/o 0.5 second Allow the tool and battery to thoroughly cool.
0000BookCJ36DA.indb180000BookCJ36DA.indb18 2023/04/0314:20:372023/04/0314:20:37
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CJ36DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CJ36DA in the language / languages: All languages as an attachment in your email.

The manual is 15.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info