816397
4
Zoom out
Zoom in
Previous page
1/124
Next page
4
English
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
Blades (No. 41, No. 123X) ..................................1 each
No. 41: Refer to Table 1
No. 123X: Mild steel plate 1.5 – 10 mm
Sub base .......................................................................1
Hexagon bar wrench .....................................................1
Splinter guard................................................................1
Dust collector ................................................................1
Chip cover .....................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various lumber and pocket cutting
Cutting mild steel plate, aluminum plate, and copper
plate
Cutting synthetic resins, such as phenol resin and vinyl
chloride
Cutting thin and soft construction materials
Cutting stainless steel plate (with No. 97 blade)
SPECIFICATIONS
Voltage (by areas)*1
(110 V, 120 V, 220 V, 230 V,
240 V)
Power Input*1 800 W
Max. cutting depth Wood 160 mm
Mild steel 10 mm
No-load speed*1 800 – 2800 min-1
Stroke 26 mm
Min. cutting radius 25 mm
Weight*2 2.7 kg (CJ160V),
2.6 kg (CJ160VA)
*1 Be sure to check the nameplate on product as it is
subject to change by areas.
*2 Weight: According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Changing blades 2 113
Adjusting the blade operating
speed*1 3113
Switch operation 4 114
How to use the LED light 5 114
Adjusting the orbital operation 6 114
Splinter guard 7 114
Sub base*2 8 115
Chip cover 9 115
Housing the hexagonal bar wrench 10 115
Mounting the guide 11 115
Rectilinear cutting 12 115
Cutting a circle or a circular arc 13 115
Cutting metallic materials 14 116
Angular cutting 15 116
Pocket cutting 16 116
Concerning cutting of stainless steel
plates 17 117
Connecting with cleaner 18 117
Selecting accessories 118
*1 The tool is equipped with two modes: “Standard Mode”
and “AUTO Mode”.
(1) Standard Mode
You can change the blade operating speed between
800 to 2800 min-1 by adjusting the dial from “1” to “5”.
(2) AUTO Mode
Depending on the workload, AUTO Mode “A” will
automatically change the blade operating speed
to 1400 min-1 or 2800 min-1. This has the e ect of
lowering vibration and noise prior to and during
operation.
Adjust the dial for the mode and speed that best suits
your task conditions and materials.
Blade operating speed
Mode Dial Blade operating speed
Standard Mode 1 – 5 800 – 2800 min-1
AUTO Mode A No load: 1400 min-1
With load: 2800 min-1
With AUTO Mode, the vibration frequency may not
reach 2800 min-1 or return to 1400 min-1 depending on
variables such as the type of work.
NOTE*2
When the sub base is attached, the blade’s protrusion
from the material being cut will be reduced by 3mm. When
the blade has been moved down to the lowest point,
check to make sure that it is protruding from the material.
SELECTION OF BLADES
Accessory blades
To ensure maximum operating e ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut. Three types
of blades are provided as standard accessories. The blade
number is engraved in the vicinity of the mounting portion
of each blade. Select appropriate blades by referring to
Table 1.
0000BookCJ160V.indb40000BookCJ160V.indb4 2022/02/0114:38:202022/02/0114:38:20
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CJ160VA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CJ160VA in the language / languages: All languages as an attachment in your email.

The manual is 12.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info