816239
13
Zoom out
Zoom in
Previous page
1/248
Next page
13
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
Tool does not operate. No remaining battery power Charge the battery.
The battery has not been properly
installed. Remove the storage battery from the battery
compartment in the tool and check for foreign
matter. Also check the battery electrodes for
soiling. Make sure that the battery is pressed in
until it clicks into place.
Foreign matter is lodged in the
blade. When there is foreign matter in the blade, remove
the battery and use a pair of tongs or similar tool
to remove it.
Take great care since the tool may start
operating when the foreign matter has been
removed.
Sap or rust may also prevent the blade from
operating. Use a wire brush or similar tool to
remove sap or rust.
The tool has been used for heavy
work. This is the e ect of a function that protects the
battery by turning o the motor when the tool
is exposed to an excessive load. Release the
switch and remove what caused the excessive
load and pull back the switch to resume work.
Tool does not trim well. The blade has become dull. Use a wire brush or other tool to remove sap
and rust and use a le or whetstone to sharpen
the blade. If these e orts fail to make the blade
sharper, the blade has reached the end of its
service life. Replace the blade with a new one.
The blade stopped because it
was used to cut a branch whose
width exceeded the blade’s cutting
capacity.
NOTE
Work that will repeatedly cause
the blade to stop will eventually
damage the motor.
Some garden trees have wood that is very hard
and may be beyond the capacity of the tool even
if it is of a width that is within normal capacity.
Use a pair of pruning shear to remove thick
branches before starting work.
An oblique cut may also exceed the capacity of
the tool since the length of the cut increases. Be
sure to trim thick branches at right angles.
Tool suddenly stopped Tool was overburdened Get rid of the problem causing the overburden.
The battery is overheated. Let the battery cool down.
Battery cannot be installed Attempting to install a battery other
than that speci ed for the tool. Please install a multi volt type battery.
0000BookCH3656DA.indb130000BookCH3656DA.indb13 2023/05/0911:26:332023/05/0911:26:33
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CH3672DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CH3672DA in the language / languages: All languages as an attachment in your email.

The manual is 8.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info