816321
18
Zoom out
Zoom in
Previous page
1/332
Next page
18
English
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 96 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Cutting metal:
Vibration emission value ah = 2.5 m/s2
Uncertainty K = 1.5 m/s2
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power
tool can di er from the declared total value depending in
the ways in which the tool is used.
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
The unit does not run/is
stopped The battery capacity is depleted Charge the storage battery.
The unit has stopped
suddenly
The unit is overloaded Get rid of the cause of the large load.
The storage battery is overheated Allow the storage battery to cool su ciently.
The band saw blade has
come loose
There is oil or grime adhering to the band
saw blade or workpiece Wipe o oil or grime that is adhering to the
band saw blade or workpiece.
The band saw blade is not installed correctly Install the band saw blade correctly.
(See “Replacing the band saw blade”)
The band saw blade is
becoming bound in the
workpiece
A band saw blade operating speed
appropriate for the workpiece is not being
used
Select the correct band saw blade operating
speed.
(See “Adjusting operating speed”)
Cutting precision is poor
The band saw blade is worn away Replace the band saw blade with a new
one.
A band saw blade operating speed
appropriate for the workpiece is not being
used
Select the correct band saw blade operating
speed.
(See “Adjusting operating speed”)
The band saw blade is not installed correctly Install the band saw blade correctly.
(See “Replacing the band saw blade”)
The gaps between the band saw blade ball
bearing supports have become wide
Correctly adjust the gaps.
(See “Inspection of band saw blade ball
bearing supports and adjustment of gaps”)
A band saw blade that is not authorized by
the manufacturer is being used Use a band saw blade that is authorized by
the manufacturer.
Su cient warm-up cuts have not been
performed
With the band saw blade operating speed
setting dial set to “1”, perform 1 or 2 warm-
up cuts with a light cutting load such as a
cylindrical rod (carbon steel, etc.) with an
outer diameter of 20 mm or less.
00BookCB3612DA.indb1800BookCB3612DA.indb18 2022/07/0116:49:022022/07/0116:49:02
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CB3612DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CB3612DA in the language / languages: All languages as an attachment in your email.

The manual is 19.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info