816321
15
Zoom out
Zoom in
Previous page
1/332
Next page
15
English
*5. How to use the LED light
The LED light will light the area at the tip of the tool when
the switch is “ON”.
The LED light will automatically power o about
15 seconds after the switch is released.
*6 Adjusting operating speed
CAUTION
Use the band saw blade circumferential speed setting
dial to select a speed that is suitable for the workpiece.
Cutting with a band saw blade or band saw blade
circumferential speed that is unsuitable for the workpiece
will decrease cutting precision, and may also result in
damage to the band saw blade.
In Standard Mode, the circumferential speed of the
band saw blade can be freely set from 1 to 5 on the
dial.
On the dial, 1 is the lowest speed and 5 is the highest
speed.
In Standard Mode, the circumferential speed that is
set with the dial is maintained even when the load
changes.
In AUTO Mode (“A” on the dial), noise can be reduced
and the duration of operation can be extended by
lowering the circumferential speed when there is no
load.
In AUTO Mode, if a load is applied during operation,
the circumferential speed is automatically increased.
(Equivalent of 5 on the dial)
Additionally, if the load becomes lighter after
cutting is completed, the circumferential speed
is automatically decreased, reducing power
consumption when there is no load.
How to recharge USB device 19 7
When charging of USB device is
completed 20 7
Selecting accessories 321
*1 How to use the Hook
The hook can be used to hang up the unit
temporarilyduring operations.
CAUTION
The hook should never be used to hang the unit on your
person.
When using the hook, check to make sure that the main
unit will not slip and fall, or become unstable by the wind,
etc.
Never hang the unit from your belt or trousers as this
could cause accidents.
*2 Adjusting the positions of bearing holders
WARNING
Securely tighten the M8 bolt.
Insu cient tightening will not only negatively a ect
cutting precision, but may also damage the band saw
blade leading to personal injury.
NOTE
Cutting with excessively large spacing between bearing
holders may shorten the life of the band saw blade or
adversely a ect cutting precision.
*3 Guide plate protrusion adjustment
In the ordinary operation, protrude the guide plate to the
A side fully.
When the guide plate strikes against the obstacles like
a wall or the like at the nishing of a cut, slide it at the
appropriate position.
*4 Switch operation
When you release the switch, the revolution of the band
saw blade will stop and the LED light will automatically
be extinguished in approximately 15 seconds.
Using a soft cloth, wipe o any foreign matter that
has adhered to the lens of the LED light, being
careful not to scratch the lens.
Scratches on the LED light may reduce the
brightness of the light.
When cleaning the lens of the LED light, do not wipe
with gasoline, paint thinner, etc.
Doing so will damage the lens.
Table 3 Operating Speed
Mode Dial Band saw blade
circumferential speed
(guideline) Uses
Standard Mode
1 Low Speed 1.0 m/s (60 m/min) Di cult-to-cut materials such as stainless steel and
alloys
Steel materials
(Thick materials including cylindrical rods,
shaped steel, and steel pipe)
(Thickness of 4.6 mm or more)
Steel materials
(Thin materials including steel pipe)
(Thickness of 4.5 mm or less)
2 1.5 m/s (93 m/min)
3 2.1 m/s (127 m/min)
4 2.6 m/s (161 m/min)
5 High Speed 3.2 m/s (195 m/min)
AUTO Mode* A
2.0 m/s (120 m/min)
(Idle operation) Steel materials
(Thin materials including steel pipe)
(Thickness of 4.5 mm or less)
3.2 m/s (195 m/min)
(Cutting operation)
* Circumferential speeds may vary from those stated above depending on operating conditions.
00BookCB3612DA.indb1500BookCB3612DA.indb15 2022/07/0116:48:582022/07/0116:48:58
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CB3612DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CB3612DA in the language / languages: All languages as an attachment in your email.

The manual is 19.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info