Manual Hikoki C3612DRA (page 13 of 420) (All languages)

816269

Zoom out

Zoom in

1/420

English

Slippery handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical

help.

Liquid ejected from the battery may cause irritation

or burns.

e) Do not use a battery pack or tool that is

damaged or modified.

Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion

or risk of injury.

f) Do not expose a battery pack or tool to fire or

excessive temperature.

Exposure to fire or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and

increase the risk of fire.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach

of children and infirm persons.

SAFETY INSTRUCTIONS FOR MITER

SAW

1. Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-

off wheels for cutting ferrous material such as

bars, rods, studs, etc.

Abrasive dust causes moving parts such as the lower

guard to jam. Sparks from abrasive cutting will burn the

lower guard, the kerf insert and other plastic parts.

2. Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely

clamped or held by hand.

If your hand is placed too close to the saw blade, there

is an increased risk of injury from blade contact.

3. The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut "freehand"

in any way.

Unrestrained or moving workpieces could be thrown at

high speeds, causing injury.

4. Push the saw through the workpiece. Do not pull

the saw through the workpiece. To make a cut,

raise the saw head and pull it out over the

workpiece without cutting, start the motor, press

the saw head down and push the saw through the

workpiece.

Cutting on the pull stroke is likely to cause the saw

blade to climb on top of the workpiece and violently

throw the blade assembly towards the operator.

5. Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your left

hand or vice versa is very dangerous.

6. Do not reach behind the fence with either hand

closer than 100mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning.

The proximity of the spinning saw blade to your hand

may not be obvious and you may be seriously injured.

7. Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always

make certain that there is no gap between the

workpiece, fence and table along the line of the

cut.

Bent or warped workpieces can twist or shift and may

cause binding on tile spinning saw blade while cutting.

There should be no nails or foreign objects in the

workpiece.

8. Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpiece.

Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with high

speed.

9. Cut only one workpiece at a time.

Stacked multiple workpieces cannot be adequately

clamped or braced and may bind on the blade or shift

during cutting.

10. Ensure the miter saw is mounted or placed on a

level, firm work surface before use.

A level and firm work surface reduces the risk of the

miter saw becoming unstable.

11. Plan your work. Every time you change the bevel

or miter angle setting, make sure the adjustable

fence is set correctly to support the workpiece and

will not interfere with the blade or the guarding

system.

Without turning the tool “ON” and with no workpiece on

the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

12. Provide adequate support such as table

extensions, saw horses, etc. for a workpiece that is

wider or longer than the table top.

Workpieces longer or wider than the miter saw table

can tip if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be thrown

by the spinning blade.

13. Do not use another person as a substitute for a

table extension or as additional support.

2023/08/31 18:21:53Stylesheet: EU Version: 2023.8.18

C3612DRA_C99749371_309_EU

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki C3612DRA in the language / languages: All languages as an attachment in your email.

The manual is 8.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hikoki C3612DRA Manual

Product: