816213

Hikoki C1805DA Manual

15
Zoom out
Zoom in
Previous page
1/272
Next page
English
15
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Rotation speed changeover function (Power mode /
Silent mode)
(Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the
operating mode. (Fig.15)
Silent mode reduces maximum motor RPM enabling
efficient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool
will automatically switch to Power mode and revert back
to Silent mode when the load decreases.
In Power mode, no change is made to Silent mode even
when the load decreases.
NOTE
○ To enable mode changes, pull the switch once after
installing the battery.
○ Do not give a strong shock to the switch panel or break
it. It may lead to a trouble.
2. Battery
Model BSL1850MA
Voltage 18 V
Battery capacity 5.0 Ah
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YFSL>
1. Connect the charger’s power cord to the
receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red. (See Table1)
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig.22 (on page 6).
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (See Table1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table1, according to the condition of the charger or the
rechargeable battery.
Table 1: Indications of the pilot lamp
ON/OFF at 0.5sec. intervals Before charging *1
or
Charging complete
Lights continuously While charging
Lights for 1sec. at intervals of
0.5sec. Overheat standby *2
ON/OFF at 0.1sec. intervals Charging impossible
*3
NOTE
*1 If the red lamp continues to blink even after the charger
has been attached, check to confirm that the battery
has been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery has cooled
down even when left in situ, the best practice is to
remove the battery and allow it to cool down in a
shaded, well-ventilated location before charging.
*3 Malfunction in the battery or the charger
– Fully insert the battery.
– Check to confirm that no foreign matter is stuck to
the battery mount or terminals. If there are no
foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
○ If the pilot lamp does not blink in red even though the
charger cord is connected to the power, it indicates that
the protection circuit of the charger may be activated.
Remove the cord or plug from the power and then
connect it again after 5minutes or so. If this does not
cause the pilot lamp to blink in red, please take the
charger to the HiKOKI Authorized Service Center.
○ When the battery charger has been continuously used,
the battery charger will be heated, thus constituting the
cause of the failures. Once the charging has been
completed, give 15minutes rest until the next charging.
(2) Regarding the temperatures and charging time of the
battery. (See Table2)
Table 2
Model UC18YFSL
Type of battery Li-ion
Charging voltage 14.4–18 V
Temperatures at which the
battery can be recharged 0°C–50°C
Charging time for
battery capacity,
approx. (At 20°C)
1.5Ah 22min
2.0Ah 30min
2.5Ah 35min
3.0Ah 45min
4.0Ah 60min
5.0Ah 75min
6.0Ah 90min
Charging time for
multi volt battery
capacity, approx.
(At 20°C)
1.5Ah
(×2unit) 45min
2.5Ah
(×2unit) 75min
4.0Ah
(×2unit) 120min
Number of battery cells 4–10
Weight 0.5kg
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
2023/08/01 12:32:25Stylesheet: EU Version: 2023.7.24
C1805DA_C99750471_308_EU
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki C1805DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki C1805DA in the language / languages: All languages as an attachment in your email.

The manual is 6.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info