167658
14
Zoom out
Zoom in
Previous page
1/24
Next page
e13
021584
FUSE
GND REM BATT+ 12V
POWER INPUT
SPEAKER OUTPUT
+ CH3 + CH4
+ MONO BRIDGED
+ CH1 + CH2
14
Installation
Battery
12 V
In-Line
Fuse
Ground-
Connection
Ground-Connection
to vehicle's chassis
Remote Wire
(REM)
Installation Notes
The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat.
Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the
mounting location you should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable
installation. It is also important to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do
not install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause damage to the
amplifiers electrical components.
Installation of the amplifier
Before starting with the installlation, mount the provided mounting brackets on the
amplifier. Mark the location for the mounting screw holes by using the amplifier as a
template. Drill holes at the marked locations as and firmly fasten the amplifier in place
with the mounting screws supplied in the accessory kit. Before drilling or cutting
any holes, investigate the layout of your automobile thoroughly. Take care when
working near the gas lines or hydraulic lines and electrical wiring.
Electrical Connection
Ground (GND)
This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading
sheet metal screw since the threads cut into bare metal. Ensure that all paint or other insulationis removed from around the hole
area, and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as
possible - use the same gauge as was used for the +12V cable. Make sure that the connection is safe and stable.
Remote (REM)
Connect the remote wire of your headunit with the remote turn-on of the power amplifier.
Battery Connection (+12V Power)
This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an in-line
fuse near by the battery. Please use a sufficient gauge (min. 25 sqmm) with spade lug with insulating sleeve.
Fuses
The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance) of
the speakers, for 2 Ohm loads the fuses may have to get increased by up to 50% in case of higher power consumption.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics zxi 9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics zxi 9000 in the language / languages: English, German as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info