700137
21
Zoom out
Zoom in
Previous page
1/32
Next page
21
FUNCTIONAL INSTRUCTIONS
Installation of RCA/Audio signal cables and power supply cables.
Ensure while installation not to lead the audio cables between the head unit and the amplier together with the power supply wires
on the same side of the vehicle. The best is a real separated installation on the left and right cable channel of the vehicle to avoid
interferences on the audio signal. This stands also for the enclosed bass-remote wire, which should not be installed together with the
power supply wires.
NOTE
8
9
11
12
10
The CH1/2 and CH3/4 HP controllers adjust the cut-off point of the frequency range to below for the relevant channels (Channel
1/2 or Channel 3/4). The cut-off frequency is continuously adjustable from 10 Hz to 1200 Hz (1.2 kHz).
The LEVEL CH1/2 and CH3/4 controllers adjust the input sensitivity of the amplier, to adjust the audio signal of the head unit at
the relevant channels (Channel 1/2 or 3/4). The input sensitivity is adjustable from 6 Volts (MIN) to 0.2 Volts (MAX).
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
When you only use the jacks CH1/2, the INPUT MODE switch must be set to 2CH position.
The LINE OUT RCA jacks provide a linear fullrange audiosignal to supply an additional amplier.
SPEAKER CABLES
SHIELD
TO THE LINE IN ON THE
AMPLIFIER
CORE CONDUCTOR
HI LEVEL INPUTS & AUTO TURN ON
If your head unit has no pre-amplier low level RCA outputs or doesn’t provide a separate remote turn on wire (like described on
page 19/#2), follow these instructions:
AUTO TURN ON
Bring the AUTO TURN ON switch to position ON to activate the auto turn on function. This function only works, if the push button
INPUT LEVEL MODE is in HI position and highlevel inputs (speaker outputs from the headunit) are connected at the LINE IN.
Please check the regarding notes below.
The amplier detects now by the so called ”DC Offset” (a voltage increase to 6 volts on the high level speaker outputs) if the
head unit is turned on and the amplier turns automatically on. As soon as the head unit is turned off, the amplier shuts down
automatically after approx.one minute.
NOTE: The AUTO TURN ON usually works with 90% of all headunits, because they are equipped with the ”High Power” outputs.
Only with a few older headunits the AUTO TURN ON function is not applicable.
The port of the remote connector of the amplier (page 19#2, REM) can now be used also to turn on additional other ampliers.
Connect the REM ports of the ampliers and ensure, that the other amplier’s AUTO TURN ON function is deactivated.
High level speaker cables as signal input:
Please use the optional HF-HLA adaptor from HiFonics (see
page 29). This adaptor is optmized for the use with this amplier
inputs and owns additionally a protect function for the speaker
outputs of your headunit.
Alternative: Solder the ends of the loudspeaker cables of the
head unit with common RCA connectors (separately available)
and connect them with LINE IN of the amplier.
The HI LEVEL INPUTS can be use independently from the AUTO
TURN ON function.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics ZRX6404 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics ZRX6404 in the language / languages: English, German as an attachment in your email.

The manual is 8,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info