700144
19
Zoom out
Zoom in
Previous page
1/28
Next page
19
FUNCTIONAL INSTRUCTIONS
INTERCONNECTION EXAMPLE
2-channel-mode: 1 x Stereo-System
INTERCONNECTION
Connect the RCA lineouts of the head unit with the RCA jacks LINE IN of the amplier with appropriate high-value RCA cables.
Connect the front and rear speakers with the speaker outputs (SPEAKER OUTPUT + L - and + R -).
Always ensure that the total impedance load on the speaker outputs is not lower than 2 ohms.
Too low impedance cause high temperature and will shut down the amplier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS
When using bigger speakers (more than 20cm) set the X-OVER switch to the FULL position (Full Range Signal).
When using smaller speakers (8.7cm - 16cm) set the X-OVER switch to the HP position (Highpass Mode) to avoid
any damage by lower frequencies on the speakers. The cut-off frequency is adjustable with the HP controller and should
be set between 60Hz to 150Hz, depending on the size of the speakers.
The LP Controller is not in use in this interconnecting example.
LEVEL CONTROLLER
Turn the LEVEL controller of the amplier to the MIN position.
Turn the volume controller of the head unit to 80 - 90% of its full setting.
Turn the LEVEL controller clockwise until you hear some distortion.
Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
BASS REMOTE
The enclosed Bass Level Controller is not in use in this interconnecting example.
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity of all connections. The interchange
of plus and minus cause total loss of bass playback and could damage the speakers.
NOTE
Connect stereo RCA output (L/R) of the
head unit with LINE IN of the amplier
HP or FULL
Loudspeaker left
2 – 8 Ohms
Loudspeaker right
2 – 8 Ohms
POWER INPUT
SPEAKER OUTPUT
LINE OUT
GND +12VREM
LINE IN
R
L
R
L
BRIDGED
RL
VXi4002
LP HP
BP
LEVEL
0dB 12dB
10Hz 1.2kHz35Hz 250Hz
MIN MAX
BASS
BOOST
FULLHPLP/BP
X-OVER MODE
PROTECT
POWER
BASS LEVEL
CONTROLLER
FUSE
POWER INPUT
SPEAKER OUTPUT
LINE OUT
GND +12VREM
LINE IN
R
L
R
L
BRIDGED
RL
VXi4002
LP HP
BP
LEVEL
0dB 12dB
10Hz 1.2kHz35Hz 250Hz
MIN MAX
BASS
BOOST
FULLHPLP/BP
X-OVER MODE
PROTECT
POWER
BASS LEVEL
CONTROLLER
FUSE
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics VXi6002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics VXi6002 in the language / languages: English, German as an attachment in your email.

The manual is 7,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info