169036
18
Zoom out
Zoom in
Previous page
1/24
Next page
18
718
Functions & Controls
TXi 3400
High Pass CH1/2 & CH3/4
This controller adjust the frequency of the
loudspeakers onward (X-OVER switch position HP).
The cut-off frequency is continuously adjustable
from 10Hz to 1200Hz.
Bass Boost CH3/4
Variable Bass Boost from 0 up to
+12dB at 45 Hz.
Line Out - RCA Outputs
RCA Outputs to send a 4CH mono
mix to an additional mono amp.
Input - RCA Inputs
Full range line input to connect with
the head unit RCA Outputs.
Level Input CH1/2 & CH3/4
Adjust the input sensitivity
from 6 Volts to 0,2 Volts.
Remote
Terminal for the provided cable remote
controller, which allows to control the bass
Power - LED (also located
on the remote controller)
If green LED lights up, the
amplifier is turned on.
Protect - LED (also located on the remote controller)
If the red LED lights up, the following matters occurs:
a) Overheating
b) Speaker wires shorted
c) Overload (Impedance, weak power supply)
d) Amplifier is damaged
The built-in electronic diagnostic protection saves the amplifier and
speakers from serious damages. If the red LED lights up due to
overheating, let the amplifier cool down a while, then turn it on again. If
the red LED still lights up, observe therefor the section “TROUBLE
SHOOTING”
Input Mode
If only CH1 and CH2 on the LINE INPUT are connected, set the switch
to position 2CH. If all channels on the LINE INPUT are connected, set
the switch to position 4CH.
Low Pass CH 3/4
This controller adjust the frequency of the
loudspeakers upward (X-OVER switch position LP).
The cut-off frequency is continuously adjustable from
30Hz to 150Hz.
X-Over CH3/4
Position LP/BP:
The Lowpass-/Bandpass-Mode is suited for
subwoofer operations. The signal will be limited
upward and only the bass frequencies will be
amplified. The cut-off frequency is adjustable by the
LOW PASS-controller.
Position HP:
The Highpass-Mode is suited for loudspeaker
operations. The signal is limited downwards and
only the mids and highs will be amplified.
The cut-off frequency is adjustable by the HIGH
PASS-controller.
Position FULL:
The Fullrange-Mode is suited for very huge
loudspeaker systems or huge backshelf systems.
Thereby the whole freqencies will be amplified.
X-Over CH1/2
Position DUPE:
In the DUPE-Mode all settings of CH 3/4 will be assigned to CH1/2.
Position HP:
The Highpass-Mode is suited for loudspeaker operations. The signal is limited
downwards and only the mids and highs will be amplified.
The cut-off frequency is adjustable by the HIGH PASS-controller.
Position FULL:
The Fullrange-Mode is suited for very huge loudspeaker systems or huge backshelf
systems. Thereby the whole freqencies will be amplified.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics txi3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics txi3400 in the language / languages: English, German as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info