700158

Hifonics TSi800-IV Manual

22
Zoom out
Zoom in
Previous page
1/28
Next page
22
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE IN CH 1 and CH 2 of the amplifier with appropriate high-value
RCA cables. If a separate SUB OUT from your headunit is available, use this as LINE OUT.
• Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.
• Ensure by any means, that the total impedance load of all subwoofers per channelpair is not lower than 4 ohms. Too low impedance
cause high temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INPUT SWITCH
• Select the 4CH position on the INPUT switch.
CROSSOVER SETTINGS CH3/4 (SUBWOOFER 1 & 2)
• In the mono/subwoofer mode the X-OVER MODE switch must set to the LPF/BPF position (Lowpass/Bandpass mode), thereby the
higher frequencies will be eliminated. The cut-off frequency ist adjustable with the LPF controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
• In the lowpass mode the HPF controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and harmful
frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 40 Hz, depending
on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.
CROSSOVER SETTINGS CH1/2
• Set the X-OVER MODE switch to DUPE. The DUPE mode passes (duplicate) the signal from CH3/4 to the line input section of CH1/2.
All controllers and settings are without function. The LINE IN RCAs of CH1/2 are deactivated.
LEVEL CONTROLLER CH3/4
• Turn the LEVEL controller of the amplifier to the MIN. position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BOOST CONTROLLER CH3/4 (SUBWOOFER 1 & 2)
• The BOOST controller adjusts the bass enhancement between 0db and +12dB @ 50 Hz. In the DUPE-mode the boost controller also
affects the bass enhancement on the channel pair CH1/2 (Subwoofer 1).
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
REMOTE BASS LEVEL CONTROLLER BLC-TSi
• The enclosed remote BASS LEVEL Controller BLC-TSi adjusts the bass-level e.g. from the driver’s seat.
In the DUPE-mode the bass level controller also affects the bass level on the channel pair CH1/2 (Subwoofer 1).
Please use only the enclosed controller and cable.
INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged
ENG|OPERATIONAL INSTRUCTIONS
INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged
BLC-TSi
Subwoofer 2
4 – 8 Ohms
Subwoofer 1
4 – 8 Ohms
R L
Connect RCA output (L/R or SUB OUT)
of the headunit with the LINE IN CH3/4 of
the amplifier
Position XOVER MODE:
LPF/BPF
Position
XOVER MODE:
DUPE
Position
INPUT: 4 CH
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics TSi800-IV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics TSi800-IV in the language / languages: English, German as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info