700115
9
Zoom out
Zoom in
Previous page
1/28
Next page
9
IMPORTANT NOTES PRIOR TO INSTALLATION
This device is only suited for a 12 volt system with negative ground.
The radiated heat while operation requires sufcient air circulation at the place of installation. It is very im-
portant that the heat sink ns do not have contact with any metal parts or any surfaces which could impair
air circulation. The amplier may not be installed in small closed location or spaces without air circulation.
We recommend the installation in the vehicle’s trunk. Ensure sufcient protection against vibrations, dust
and dirt.
Ensure that the input and output cables are sufciently separated from the power supply cables. Otherwise
interferences may occur.
Ensure the accessibility of the fuse and the operating elements after installation.
The reliability and performance of the amplier depends on the quality of installation. Preferably consult an
expert to install the system.
Avoid any damage or removing of the components of the vehicle like wires, cables, board computer, seat
belts, gas tank or the like.
POWER SUPPLY AND TURN-ON-CONNECTION
ATTENTION: Before you start with the installation, disconnect the ground connection from the ve-
hicle’s battery in order to prevent short circuits.
The power wiring which is usually installed in on-board car networks is not sufcient for a power amplier‘s
demands. Make sure that the power wires to GND and to the +12 V terminal has been sufciently specied.
First connect the GND terminal [ 6 ] of the amplier to an appropriate ground connection at the chassis. To
ensure a good connection, residue dirt and dust from the connection point. A loose connection may cause
malfunctions or interferences noise and distortion.
Then connect the +12 V terminal [ 4 ] of the amplier with the battery by using an appropriate cable including
an in-line fuse. This fuse [ 2 ] should be located very close to the battery [ 1 ]; for safety reasons not more than
30 cm away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been
accomplished.
Then connect the remote turn-on-wire [ 3 ] from the head unit with the amplier‘s REM terminal [ 5 ]. A cable
with a cross-section of 0.5 mm
2
is adequate.
LPF
BASS BOOST
LEVEL
PHASE
SHIFT
AUTO
TURN ON
X-OVER SLOPE
FUSE
50Hz
12dB 18dB
150Hz
0dB 12dB
MIN MAX
REM GND+12V
POWERPROTECT
AUDIO INPUT
HI LEVEL INPUT BASS LEVEL CONTROLLER
+ +
180°
ON
OFF
L
L R
L
R
R
POWERED SUBWOOFER STATION
HIGH EFFICIENCY CLASS D AMPLIFIER
200 WATTS RMS / 400 WATTS MAX.
ZEUS ZX 82 A
POWERED SUBWOOFER STATION
HIGH EFFICIENCY CLASS D AMPLIFIER
300 WATTS RMS / 600 WATTS MAX.
TITAN TDA 200 R
POWERED SUBWOOFER STATION
HIGH EFFICIENCY CLASS D AMPLIFIER
300 WATTS RMS / 600 WATTS MAX.
TITAN TDA 250 R
700 x 200 x 200 x
45 x 14 mm 45 x 14 mm 45 x 14 mm
+
32 4 651
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics TDA200R - TDA250R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics TDA200R - TDA250R in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info