700163

Hifonics Mercury II Manual

24
Zoom out
Zoom in
Previous page
1/32
Next page
9
1
The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.
By connecting only the CH1/2 jacks, the INPUT switch must be set to the 2CH position.
3
The HPF controller (HIGHPASS) of CH1/2 and CH3/4 adjusts the cut-off point of the frequency range to below for each channelpair.
The cut-off frequency is continuously adjustable from 10 Hz to 1200 Hz (1.2 kHz).
6
The CH1/2 X-OVER MODE switch selects the required operation mode of this channelpair.
Position DUPE: This mode should be selected, if you want to run 2 subwoofers bridged in LPF/BPF mode. The DUPE mode
passes (duplicate) the signal from CH3/4 to the line input section of CH1/2. All controllers and settings except the LEVEL controller
are then without function. The LINE IN RCAs of CH1/2 are deactivated.
Position HPF: Highpass mode (the higher frequencies will be eliminate. Adjustable by the HPF controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified).
ENG|MERCURY IV
24
7
The CH3/4 BOOST controller defines the bass bosst from 0 to 12dB @ 50Hz on channelpair 3/4.
9
FUNCTIONS AND OPERATIONAL CONTROLS
2
The LINE OUT RCA jacks provide a summed mono audiosignal to supply an additional subwoofer amplifier.
4
The LPF controller (LOW PASS) on CH3/4 adjusts the cut-off point of the frequency range to above. The cut-off frequency is
continuously adjustable from 30 Hz to 150 Hz.
5
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit for each channelpair.
The input sensitivity is adjustable from 6 Volts (MIN) to 0.2 Volts (MAX).
The BASS LEVEL CONTROLLER port is for the cable of the enclosed bass remote controller. With this bass remote controller,
you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote controller and cable.
The controller works only in LPF/BPF and only on CH3/4. In DUPE mode operation it also works on CH1/2. For more details check
the information on page 21, section #8.
11
The CH3/4 X-OVER MODE switch selects the required operation mode of this channelpair.
Position LPF/BPF: Lowpass mode (the higher frequencies will be eliminated. Adjustable by the LPF controller.)
The HPF controller works in this operation mode as subsonicfilter and eliminates the lower frequencies (Bandpass-Mode).
NOTE: If this controller is turned to a higher value than the LPF controller, no sound is hearable.
Position HPF: Highpass mode (the higher frequencies will be eliminate. Adjustable by the HPF controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified).
7
The INPUT switch must be in 2CH position, if you connect only one RCA stereo audio cable on the CH1/2 LINE IN.
Select position 4CH, if you connect two RCA stereo audio cables on CH1/2 and CH3/4 line inputs. The fader function of your
headunit works only in the 4CH mode. If you have select the 2CH mode, the input signal of LINE INPUT CH1/2 will be passed
to CH3/4. Due to this, only one RCA stereo audio cable is required and no Y-Adaptors are required.
8
864321 10 115
POWER/PROTECT (Also located on the supplied Bass Level Controller)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Observe in this case the chapter TROUBLE SHOOTING.
10
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Mercury II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Mercury II in the language / languages: English, German as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info