700163
21
Zoom out
Zoom in
Previous page
1/32
Next page
1
The LINE OUT RCA jacks provide a linear fullrange audiosignal to supply an additional amplifier.
3
The HPF controller (HIGH PASS) adjusts the cut-off point of the frequency range to below. The cut-off frequency is continuously
adjustable from 10 Hz to 1200 Hz (1.2 kHz).
6
The BOOST controller defines the bass bosst from 0 to 12dB @ 50Hz.
MERCURY II|ENG
21
8
POWER/PROTECT (Also located on the supplied Bass Level Controller)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Observe in this case the chapter TROUBLE SHOOTING.
9
FUNCTIONS AND OPERATIONAL CONTROLS
2
The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.
4
The LPF controller (LOW PASS) adjusts the cut-off point of the frequency range to above. The cut-off frequency is
continuously adjustable from 30 Hz to 150 Hz.
5
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit.
The input sensitivity is adjustable from 6 Volts (MIN) to 0.2 Volts (MAX).
7
8
97654321
The X-OVER MODE switch selects the required operation mode of the amplifier.
Position LPF/BPF: Lowpass mode (the higher frequencies will be eliminated. Adjustable by the LPF controller.)
The HPF controller works in this operation mode as subsonicfilter and eliminates the lower frequencies (Bandpass-Mode).
NOTE: If this controller is turned to a higher value than the LPF controller, no sound is hearable.
Position HPF: Highpass mode (the higher frequencies will be eliminate. Adjustable by the HPF controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified).
The BASS LEVEL CONTROLLER port is for the cable of the enclosed bass remote controller and only to use in the MASTER
mode. With this bass remote controller, you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the
enclosed bass remote controller and cable. The controller works only in LPF/BPF mode.
The Remote operates strictly as a level attenuator. At full clockwise rotation at maximum position the level will be the same as if
the Remote was not connected at all. Find at first the desired bass level without the Remote and use the Remote then as level
attenuator for the bass level.
You find also two LEDs (POWER/PROTECT) on the Remote Controller. Check #9 for more information.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Mercury II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Mercury II in the language / languages: English, German as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info