505734
5
Zoom out
Zoom in
Previous page
1/16
Next page
3
GLX60.4 / GLX100.4 4-CHANNEL AMPLIFIER APPLICATIONS
POWER INPUT
GND REM BATT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT RIGHT LEFT
- + - + - + - +
BRIDGED
BRIDGED
FUSE
LINE INPUT
REMOTE
POWER
PROTECT
LINE OUT
HI FULL LP/BP
HI FULL LP/BP
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
HI PASS LOW PASS
BASS EQ
LEVEL
X-OVER
1
/
2 CH
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
X-OVER
3
/
4 CH
HI PASS LOW PASS
BASS EQ
LEVEL
MODE
CH2-CH4
L
R
L
R
L
R
CH1/2 CH3/4
POWER INPUT
GND REM BATT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT RIGHT LEFT
- + - + - + - +
BRIDGED
BRIDGED
FUSE
LINE INPUT
REMOTE
POWER
PROTECT
LINE OUT
HI FULL LP/BP
HI FULL LP/BP
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
HI PASS LOW PASS
BASS EQ
LEVEL
X-OVER
1
/
2 CH
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
X-OVER
3
/
4 CH
HI PASS LOW PASS BASS EQ LEVEL
MODE
CH2-CH4
L
R
L
R
L
R
CH1/2 CH3/4
4 CHANNEL FULL RANGE SYSTEM
2 or 3 CHANNEL SYSTEM
- HI PASS: N/A
Here we show how to use the 4 channel amplifiers as straight forward discrete 4
- LOW PASS: N/A
channel full range units.
Interconnect cable checklist:
Channels 3/4:
- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
- HI PASS: N/A
- LOW PASS: N/A
Switch setting checklist:
- 1/2CH X-OVER: FULL
Level control checklist:
- 3/4CH X-OVER: FULL
- Refer to the section “Setting up systems after installation for best performance”
Minimum final loudspeaker impedances:
Crossover frequency control checklist:
- 2 ohm per channel.
Channels 1/2:
Switch setting checklist:
Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking
- 1/2CH X-OVER: FULL
advantage of the mono bridging capability of all Hifonics amplifiers.
- 3/4CH X-OVER: LP/BP
The following example shows how to create a 3 channel system by mono
bridging channel pair 3 / 4. In order to create a 2 channel system, simply follow
Crossover frequency control checklist:
the example to also mono bridge channel pair 1 / 2.
Channels 1/2:
- HI PASS: N/A
Interconnect cable checklist:
- LOW PASS: N/A
- Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head
unit with good quality RCA cables.
Channels 3/4:
- A MONO signal source is required to bridge channel pair 3/4, such as would be
- HI PASS: N/A
available from the mono sub bass output of an active crossover, whether
- LPF: 11 o’clock
standalone, or built into a head unit or equalizer. If you only have 1 set of RCA
outputs from your headunit, you can simply connect those to the inputs for ch
TIP: If you are using the mono sub bass output of an active crossover, there is
1/2 and switch the MODE to 2ch. The amplifier will auto sum the signal and
nothing wrong with switching in the low pass filter in these amplifiers for a
provide mono output for bridged channels 3/4 once the X-OVER is switched to
steeper low pass rolloff.
LP/BP.
Important: Do not be tempted to connect the hot, or positive outputs, from any
Level control checklist:
source together to obtain a mono signal, as this could very well damage the
- Refer to the section “Setting up systems after installation for best performance”
output stage of that source.
- It is necessary to feed the SAME signal to both left and right inputs via a Y-
Minimum final loudspeaker impedances:
adapter RCA cable.
- 2 ohm per channel in stereo mode.
- Connect the mono speaker positive terminal to the LEFT +, and its negative
- 4 ohm mono bridged.
terminal to RIGHT - as shown.
STEREO LINE INPUT
MONO LINE INPUT
(Unless using procedure
listed above for 3ch)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Gladiator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Gladiator in the language / languages: English as an attachment in your email.

The manual is 4,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info