700130
19
Zoom out
Zoom in
Previous page
1/32
Next page
19
ELECTRICAL INTERCONNECTION
INSTALLATION INSTRUCTIONS
4
1
2
3
BEFORE CONNECTING
For the professional installation of a sound system, car audio retail stores offers appropriate wire kits. Ensure a sufcient prole section
(at least 35 mm
2
), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-
streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are xed tight after
the installation, because loose connections cause malfunctions, insufcient power supply or interferences.
LOGO
This push button switches the logo illumination on the upper side from blue to white.
GND
Connect the GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short
as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it if required. Use a ground wire with a sufcient cross section (at least 35 mm
2
) and the same size like the
plus (+12V) power supply wire.
REM
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your head unit with the REM-terminal of the
amplier. Use therefor a suitable cable with a sufcient cross section (0,5 mm
2
). Hereby the amplier turns on or off with your
headunit.
BATT+12V
Connect the BATT+12V-terminal with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufcient cross section
(at least 35 mm
2
) and install an additional in-line fuse. For safety reasons the distance between the fuseblock and the battery
should be shorter than 30 cm. Do not set in the fuse into the fuseblock until the installation is accomplished.
WARNING The ampliers BRX4000D, BRX6000D and BRX 9000D have due to construction-conditioned reasons no internal fuse-
protection. The ampliers must necessarily be fused with an external In-Line-Fuse.
The fuse rating always depends on the total impedance. Please refer to our recommended fuse ratings on page 26.
1 32 4
POWER INPUT
SPEAKER OUTPUT
PROTECT
POWER
SLAVEMASTER
LP
LEVEL
BASS LEVEL
CONTROLLER
AUTO TURN ON
(ONLY IN HI LEVEL INPUT MODE)
0dB 18dB
LINE IN SLAVE IN/OUT
LEVEL
INPUT
MODE
35Hz 250Hz
L
R
MIN MAX
OFF
ON
LOW
HI
SUB
BOOST
Q-CONTROLPHASE
FREQ.
RANGE
SUB SONIC
15Hz 55Hz
GND +12VREM
EXTENDED BASS CONTROL
WIDE NRW20Hz 80Hz
0° 180°
BALANCED
INPUT
BRX4000 D
L
R
BRX4000 D
BLUE / WHITE
LOG0
IMPORTANT NOTE
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics BRX6000D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics BRX6000D in the language / languages: English, German as an attachment in your email.

The manual is 10,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info