505732
9
Zoom out
Zoom in
Previous page
1/16
Next page
INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS
L L
R R
SUB
IN
OUT
POWER
PROTECT
OUTPUT
MASTER
INPUT
SLAVE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BATT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS
L L
R R
SUB
IN
OUT
POWER
PROTECT
OUTPUT
MASTER
INPUT
SLAVE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BATT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS
L L
R R
SUB
IN
OUT
POWER
PROTECT
OUTPUT
MASTER
INPUT
SLAVE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
BATT+12V GND
POWER INPUT
SPEAKER OUTPUT
REM - - + +
DUAL AMP INSTALLATION PROCEDURE:
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
5. Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.
puts with good quality RCA interconnect cables.
- Be sure to remove any paint or primer from the ground point.
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
Master amp. This will allow the Master amp to control both Master and Slave amps
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
with just one Bass Remote.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
7. Connect the subwoofer(s) in accordance to the diagrams below.
Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
crossover switches will control both the Master and Slave amps. The Slave amp
shown below.
crossover switches will be bypassed.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the HFR-3 remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional “Y-Adaptor” as shown.
BE2500.1D MONO AMPLIFIER APPLICATIONS
Basic application
HFR-3
MIN MAXX
BOOST
+12V GND
POWER
SPEAKER
REM
+
-
+
-
MONO
SUBWOOFER
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY + 12 Volts
VIA FUSE
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
Linking two amps for single or dual subwoofer application
Amplifiers are stable to 2-Ohms linked
7
HFR -3
MIN MAXX
BOOST
12 GAUGE JUMPER WIRE
RCA JUMPER CABLE
MASTER OUTPUT TO SLAVE INPUT
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
Master remote controls
both amplifiers when
LINKED
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
(MASTER)
(SLAVE)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics Brutus Elite BE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics Brutus Elite BE in the language / languages: English as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info