488783
42
Zoom out
Zoom in
Previous page
1/44
Next page
42
7 Additional information
It’s often easy to mistake incorrect operation for trouble and malfunction of the unit. If you think there is
something wrong with the component, check the points below first. If the problem persists, contact you
nearest HHB authorized service center and have them check over the unit.
Symptom Cause Remedy
Power cannot be
turned on.
The power cord is unplugged from the wall
outlet.
The power plug is not firmly connected to
the recorder.
Plug the power cord into a
power outlet.
Make sure that the power plug is
fully inserted in the recorder.
No sound is heard
during playback.
The recorder is not connected up properly.
Check all connections, especially
to the amplifier (p.10–11).
Cannot record.
The recorder is not connected up properly.
The CD-R or CD-RW disc in use has already
been finalized.
The input selection is incorrect.
The REC LEVEL control is set too low.
Check all connections (p.10–11)
Use a non-finalized disc or erase
the CD-RW disc (p.38).
Select the input for the correct
input source to the recorder.
Increase the recording level
(p.23–24).
Recorded sound is
distorted.
The REC LEVEL control is set too high.
Signal connections are incorrect.
There is interference from external
sources.
The disc is damaged or warped.
The disc is extremely dirty.
Reduce the recording level (p.23
–24).
Check all connections (p.10–11)
Turn the power off to other units
near the recorder until there is no
interference.
Use another disc.
Clean the disc.
Remote control
operation is
impossible.
The remote control batteries are
exhausted.
There is an obstacle between the remote
control unit and main unit.
The remote control unit is being operated
outside the remote controllable range.
Replace both of the remote
control batteries with new ones.
Remove the obstacle.
Operate in the remote
controllable range (p.9).
Some tracks are
skipped without
being played.
The SKIP PLAY button is set to on. Set the SKIP PLAY button to off
(p.28).
Skip playback does
not occur.
The SKIP PLAY button is set to off. Set the SKIP PLAY button to on
(p.28).
The recorder does
not recognize the
end of tracks
during sync
recording.
The level that the recorder regards as
‘silence’ is set either too low, or too high.
Set the silence threshold to a
suitable level for automatically
numbering tracks (p.33).
A recorded CD-R
disc cannot be
played on other CD
players.
The disc has not been finalized after
recording. When such a disc is loaded, the
CD-R indicator lights up.
The pickup lens of the other CD player is
dirty, impairing its ability to play CD-R discs.
Finalize the disc (p.26).
Try the disc on a different CD
player. If it plays OK then get the
pickup lens on the original player
cleaned.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HHB CDR-830 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HHB CDR-830 in the language / languages: English as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info