761542
50
Zoom out
Zoom in
Previous page
1/126
Next page
MY20H02-12_1.0_12.06.2019 50
Assembly
5.3.4.2 Adjusting the FOX quick release
Figure 46: Structure of quick release from rear with (1)
axle nut lock, (2) axle nut securing screw, (3) directional
arrow, (4) axle setting value and (5) axle nut
Record the axle setting value (4) indicated by
the directional arrow (3).
Loosen the axle nut securing screw (2) with a
2.5 mm hex key by approx. four revolutions,
but do not remove the screw completely.
Turn the quick release lever to the open
position and loosen the axle by approx. four
revolutions.
Press the axle inward from the side of the open
lever. This pushes out the axle nut securing
screw so that you can turn it out of the way.
Push the axle further forward and turn the axle
nut clockwise to increase the lever tension or
anti-clockwise to reduce the lever tension.
Reinsert the axle nut lock and tighten the screw
to 0.9 Nm (8 in-lb).
Repeat the steps for installing the axle to check
proper installation and correct adjustment.
5.3.4.3 Mounting the wheel with Kabolt axles
The procedure for installing the 15 x 100 mm and
15 x 110 mm Kabolt axles is the same.
Place the front wheel in the fork ends of the
fork. Push the Kabolt axle through the fork end
on the non-drive side and hub.
Figure 47: Pushing the Kabolt axle in
Tighten the Kabolt axle screw to 17 Nm
(150 in-lb) with a 6 mm hex key.
5.3.4.4 Checking the stem and handlebars
Checking connections
Stand in front of the pedelec to check whether
the handlebars, stem and fork steerer are
firmly attached to one another. Clamp the front
wheel between your legs. Grasp the handlebar
grips. Try to twist the handlebars towards the
front wheel.
The stem must not move or twist.
Firm hold
Place your entire body weight on the
handlebars with the quick release lever closed
to check that the stem is firmly in place.
The handlebars shaft must not move
downwards in the fork steerer.
If the handlebars shaft should move in the fork
steerer, increase the quick release lever
tensioning. To do so, turn the knurled nut
slightly in a clockwise direction with the quick
release lever open.
Close the lever and check the stem is firmly in
position.
1
2
3
45
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hercules BOSCH Intuvia Pedelec Display 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hercules BOSCH Intuvia Pedelec Display 2021 in the language / languages: English as an attachment in your email.

The manual is 13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hercules BOSCH Intuvia Pedelec Display 2021

Hercules BOSCH Intuvia Pedelec Display 2021 User Manual - German - 169 pages

Hercules BOSCH Intuvia Pedelec Display 2021 User Manual - Dutch - 165 pages

Hercules BOSCH Intuvia Pedelec Display 2021 User Manual - French - 169 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info