647375
11
Zoom out
Zoom in
Previous page
1/43
Next page
BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL
Version 06.03 DIG.EN 11
STARTING AND OPERATING THE MACHINE
ON/OFF SWITCH MASTER SWITCH
The ON/OFF switch is used to turn the machine on and off before and after operation.
CAUTION – The ON/OFF switch does not completely turn off all power to the machine. With the BOXER series, MARLIN
42, MARLIN 42 XL and other models which run on 1 phase power, it is necessary to unplug the power cable from the
wall socket before the machine is completely without power. With the other MARLIN models, FALCON series, POLAR
series and other models which run on 3 phase power, it is necessary to turn off the master switch before the machine is
completely without power. Ensure that the machine is completely without power during maintenance and repair activities.
BOXER series / MARLIN 42 & 42 XL
When the machine is turned on (with the ON/OFF switch), the pump only runs during the vacuum cycle.
MARLIN / FALCON / POLAR series
When the machine is turned on (with the ON/OFF switch), the pump runs continuously. The 3 phase pumps need more
time to warm up and turning them on and off has a detrimental effect on their lifespan. If the machine is turned on, but it
is not used, the pump will automatically turned off after 10 minutes. This to prevent overheating from the oil, and reduce
unnecessary pollution from exhaust filters. We call this function Sleeper function.
SLEEPER FUNCTION
On the models: Marlin, Falcon and Polar, the sleeper function id default switched on. This means if the machine is
switched on but not ued, the pump automatically switches of after 10 minutes. By closing the lid the cycle and the pump
will start simultaneously. Contact the supplier or Henkelman BV for more information on the sleeper function.
STARTING THE MACHINE
When the machine is connected and the master switch is switched to 1 (if applicable) then the machine can be turned on
using the ON/OFF switch. When starting the machine two codes first appear in succession on the large display before
control panel switches to operation mode.
The first code indicates the model of the machine
. The second code indicates the control software
version. Note both codes on page 4 as they are important for the supplier or Henkelman BV when
making enquiries and/or if any problems arise.
After switching to operation mode the machine is ready for use. If the machine is new or has been
unused for a longer period of time then it is advisable to run the pump conditioning program (15
minutes) to heat up and clean the pump. For instructions on the conditioning program, see page 22.
After switching to the operation mode the display could read [ OIL ]. This means that the operating
hours counter is turned on and the set number of operating hours has elapsed. The hour counter is
turned off by default but the client or supplier can activate it as a reminder for regular maintenance
activities.
When [ OIL ] is displayed the machine can be still be used as usual but it is advisable to either turn off
the hour counter or to reset it. More information on how to set or turn off the operating hours counter
can be found on page 17.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Henkelman POLAR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Henkelman POLAR in the language / languages: English as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Henkelman POLAR

Henkelman POLAR User Manual - German - 44 pages

Henkelman POLAR User Manual - Dutch - 43 pages

Henkelman POLAR User Manual - French - 46 pages

Henkelman POLAR User Manual - Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info