647376
19
Zoom out
Zoom in
Previous page
1/32
Next page
USER MANUAL JUMBO SERIES
Version 06.03 JUM.EN 19
Replace sealing wire and teflon tape on Mini Jumbo and Jumbo Plus (only single seal)
1. Remove the sealing bar from the holders by unscrewing the screws
2. Remove the teflon tape from the sealing bar.
3. The old sealing wire can be removed by unscrewing the clamp bands and pulling the
wires from the plate or groove.
4. Degrease the sealing bar with a clean cloth.
5. Cut a new piece of sealing wire to the length of the sealing bar plus about 15 cm (± 6
inches).
6. Push one end of the wire through the clamp plate or grooves on the side or bottom of
the sealing bar and screw down.
7. Clamp the sealing bar with the top facing down in a vice and pull the sealing wire
through the clamp plate or groove on the other side of the sealing bar.
8. Pull the wire taught with a pair of pliers and screw it down at the same time. Ensure
that the wire is pulled tight and straight prior to screwing down the wires.
9. It is handy to use a pair of pliers as a lever for optimal wire tension. Grip the end of
the sealing bar in a vice and tension the wire by pressing the bar down.
10. Cut the protruding wire ends off on both sides directly past the screws.
11. Cut a piece of teflon tape as long as the sealing bar plus about 5 cm (± 2 inches).
12. Stick new teflon tape straight over the new sealing wire. Ensure that the teflon is
straight on the sealing bar and that the sticky part is stuck on the side. Ensure that
the teflon is stuck on the bar smoothly and without folds.
13. Cut the teflon tape off so that the sticky part does not get stuck on the sides of the
clamps but that the teflon extends over the top of the clamps.
14. Place the sealing bar back in the machine. Ensure that the sealing bar is properly
clicked onto the holders or that the screws are hand-tight screwed in.
Remove teflon ta
p
e
Unscrew and remove
sealing wire
Screw sealing wire down
under a clamp plate.
Pull the wire tight in
second clamp plate using
a pair of pliers and a vice.
Cut off the ends of the
sealing wire and stick
teflon tape tightly on the
beam without folds.
See page 22
for correct parts and quantities
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Henkelman Jumbo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Henkelman Jumbo in the language / languages: English as an attachment in your email.

The manual is 3,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Henkelman Jumbo

Henkelman Jumbo User Manual - German - 31 pages

Henkelman Jumbo User Manual - Dutch - 32 pages

Henkelman Jumbo User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info