647374
12
Zoom out
Zoom in
Previous page
1/43
Next page
BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL
Version 06.03 DIG.EN 12
STANDARD OPERATING STEPS FOR THE MACHINE
1. Turn the machine on with the ON/OFF switch. Heat up the pump with the condition program when machine has
stood idle for some time (instructions page 22).
2. Fill the vacuum bag with product. Select the correct format bag that easily fits around the product but is not too
large for the product. Ensure hygienic conditions during this operation. Packaging materials, product and hands
must be clean and if possible dry.
3. Lay the vacuum bag in the chamber or on the working plate. The open side must be
laid over the sealing bar or silicone holder. The bag may however not extrude from
the chamber. If the product is a lot lower than the height of the sealing bar or silicone
holder then insertplates which are supplied standard with the machine can be used.
This makes the operation easier and reduces the cycle time.
4. The vacuum bag must be laid without folds over the sealing bar (BOXER and
MARLIN) or silicone holder (FALCOM and POLAR).
5. For a gas flush system the opening of the vacuum bag must be pulled over the gas
nozzles (see illustration).
6. Multiple vacuum bags can be placed over the sealing bar/silicone holder if the sealing
bar/silicone holder is longer than the vacuum bag. Vacuum bags may not however be laid
on top of each other on the bar/holder. If there are multiple bars/holders then all bars/holders can of course be used
during the same cycle.
7. Use the [PROG] key to choose the desired program. See page 18 for instructions about programming.
8. Close the lid and the machine automatically runs through the full cycle of all activated functions. The lid opens
automatically when the last function “ventilation” has been completed.
9. If necessary the cycle can be partially or fully interrupted by pressing the [VACUUM STOP] key or the [STOP] key.
The [VACUUM STOP] key interrupts the active function (vacuum, gas flushing, sealing, or soft-air ventilation) and
automatically continues with the next function.
The [STOP] key interrupts the entire cycle and goes immediately to the ventilation function.
10. After cycle completion, the packed product (or products) can be removed from the machine.
11. If the machine is equipped with a cut-off sealing system then the remaining flap on the vacuum bag can be torn off.
SAFETY and PRODUCT PROTECTION
The packing process can be partially or fully interrupted at all times:
Stop active function, press [VACUUM STOP] key
Stop full machine cycle, press [STOP] key
OPTIMAL AND EFFICIENT PACKAGING RESULT
Use the correct size and good quality vacuum bags
Maximum 75% product filling in vacuum bag
Place vacuum bag fold free over sealing bar/silicone holder (use correct number in insertplates in chamber)
Pull vacuum bag far enough over gas nozzles (for gas flush) so that no gas is lost and the bag does not
move during gas flushing
BOXER / MARLIN series
FALCON / POLAR series
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Henkelman FALCON at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Henkelman FALCON in the language / languages: English as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Henkelman FALCON

Henkelman FALCON User Manual - German - 44 pages

Henkelman FALCON User Manual - Dutch - 43 pages

Henkelman FALCON User Manual - French - 46 pages

Henkelman FALCON User Manual - Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info