741199

Hendi KP 96 Manual

10
Zoom out
Zoom in
Previous page
1/15
Next page
_ Hob _ rev. 0 _____________________________________________________________________ KP 96 – KTP 96 _
_ CATEGORY II2H3+ _ GB __
0705
______________________________________________________ page 10 _
6. Adapting cook-top to different types of gas
To adapt the cook-top to a different type of gas from the one used to test the device in the factory
(see data plate or supplementary plate), replace the nozzles of the five burners and set the primary air
flow by means of the appropriate tools. To do so it will be necessary to disassemble the cook-top in
order to easily access the burners, the nozzle holders and the tools used to adjust the primary air.
Proceed as follows:
- Remove the pot support grids from the
cook-top and remove the mobile parts of
the burners from their position.
- By means of the tool provided, unscrew
the threaded ferrules “A” (Fig. 3) securing
the burners to the cook-top.
- Remove the chromium plated rings “B”
ensuring not to damage the cables
connected to the ignition plugs.
- Remove the elastic rings “C” securing the
thermocouples to the cook-top.
- Unscrew the 3 screws securing the
central burner (triple crown) to the cook-
top.
- Unscrew the 4 screws securing the cook-
top which are located on the two sides of
the cook-top itself.
- Carefully lift the cook-top and remove it,
so that the burner area can be easily
accessible.
- Replace the “U” nozzles with those that
are more suitable for the new type of gas
(check table 1), making sure that the
correct diameter is stamped on them.
- Set the new primary air intake regulating
the right distance between the
adjustment tools positioned at the
entrance of the “Venturi” pipe of the
burners.
- For fast and semi-fast burners (Fig. 4)
loosen the check nut “D”, rotate the
ferrule “G” so as to adjust the distance
between the ferrule and the nozzle holder
“P” to an H value indicated in table 1.
Tighten the check nut “D”.
- For the triple crown burner (Fig. 5),
loosen the “V” screw securing the
adjustment bush “B” and set the bush to
Fig. 4
Fig. 5
Fi
. 3
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi KP 96 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi KP 96 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info