Manual Hendi KC 96 V (page 10 of 26) (English)

741192

Zoom out

Zoom in

1/26

_ TECNOEKA Srl _________________________________________________________ use and instruction manual _

_ page 10 ________________________________________________________________________________________

Connection of power cable

Mod. KCP96 V - KCP96 VS – KCR 96 V - The terminal board is on the rear panel of the

appliance. Open the terminal board cover by obtaining leverage with a screwdriver on the two

side fins. Loosen the cable gripper screw and allow the cable to pass through it. Arrange the

conductors so that the earth conductor is the last to detach from its terminal if the cable goes

into a state of faulty traction.

Connect the phase conductor to the terminal marked with the letter "L", the neutral

conductor to the terminal marked with the letter "N" and the earth conductor to the terminal

marked with the symbol . Tighten the ring-nut of the cable gripper and close the terminal

board cover. The appliance must be connected to an equipotential system whose efficiency

must first be checked according to current legal regulations. This connection must be made

between different appliances by using the appropriate terminal marked with the symbol . The

equipotential conductor must have a minimum diameter of 10 mm

The equipotential terminal

is at the rear of the appliance. When the appliance is operating, the supplied voltage must not

deviate from the nominal voltage value of ±10%.

Mod. KCP5 96 V – KCP5 96 VS – KC 96 V – KC 96 VS – KC 96 M – KC 96 MS

- For access to

the terminal board, remove the rear panel of the appliance. Loosen the cable gripper and allow

the cable to pass through. Locate the conductors so that the earth cable is the last to detach

from its terminal in the event of reverse pulling. Connect the phase conductors on the terminals

marked “L1” and “L2”, the neutral conductor to the terminal marked “N”, and the earth

conductor to the terminal marked with symbol according to the following lay-out:

380 - 400V~ 2N

N L

(this electrical connection lay-out is also available near the power supply terminal board).

Tighten the cable gripper and re-fit the rear panel of the appliance. The appliance must be

connected to an unipotential system whose efficiency must be suitably verified according to

current legal regulations.

This connection must be made between different appliances using the terminal marked with

the symbol

. The unipotential conductor must have minimum diameter of 10 mm

. The

unipotential terminal is located low down at the rear of the appliance.

The power cable must comply with the following characteristics:

KCP96 V – KCP96 VS

KCR 96 V

KCP5 96 V – KCP5 96 VS – KC 96 V – KC 96 VS

KC 96 M – KC 96 MS

Power supply voltage (V~) 220 – 230 380 – 400 2N

Power cable diameter 3x1.5 mm

4x2.5 mm

Type of power cable H07RN-F

Safety device - The appliance is supplied with a manually resetting thermal breaker to protect

against excessive, dangerous temperatures which could be accidentally generated inside the

oven. If tripped, the device cuts out electrical power to the appliance. To access this device,

remove the panel at the rear of the appliance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi KC 96 V in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hendi KC 96 V

Hendi KC 96 V User Manual - German - 26 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi KC 96 V Manual

Product: