741113

Hendi 282588 Manual

6
Zoom out
Zoom in
Previous page
1/72
Next page
6
EN
Preparation for first use
• Check to make sure the appliance is undamaged.
In case of any damage, contact your supplier im-
mediately and do NOT use the appliance.
• Remove all the packing material and protection
film (if applicable).
• Place the appliance on a level and steady surface,
unless mentioned otherwise
Operation
NOTE: For hygienic purposes please thoroughly
clean the device before using it. (see ---> clean-
ing)
Operate the device following the steps below:
• Fit the crank handle on the on fast speed gear
system (Figure 1) and rotate it clockwise to lift
the plunger.
• Remove the cylinder for cleaning (Figure 2). Re-
move the plunger for cleaning (See--->Plunger
Assembly/Disassembly).
• Clean the appliance (See ---> Cleaning)
• Having completed the cleaning, install the plung-
er and cylinder in its initial position separately.
Make sure it is properly locked in place.
• Fit the funnels on the sausage outlet and screw it
tight with a locking nut (Figure 3).
• Apply a food grease lubricant(not included) to the
inner surface of the Canister before filling the
meat mixture(Figure 4).
• Filling the properly installed cylinder with meat
and put sausage casing on the funnels.
• Last step: Switch the crank handle to low speed
and turn it clockwise to lower the plunger. The
meat will start to come out of the nozzle and into
the casing. Form a sausage.
• After the stuffing is finished, remove as much
residue as possible with hot water. You can also
clean the appliance with a brush/cloth and suit-
able detergent approved for use with meat pro-
cessing equipment.
Note: This will dissolve and remove any grease, oils
and protein that bacteria may feed on. Rinse again
with warm clean water to remove the detergent
solution, oils, grease and proteins. The product
may be dried using compressed air. Before reas-
sembling make sure that all parts are dry.
Plunger Assembly/Disassembly
• Slide the Plunger seal onto the Plunger (figure 5).
• Assemble the Pressure Release Valve Kit onto
the Plunger. From the top of the Plunger, place
the Washer onto the Valve Hole, then insert the
Screw through the Washer and into the Valve
hole. From the underside of the Plunger, place
the Spring onto the end of the Screw and twist
to secure.
• Screw the Plunger Bolt onto the Plunger Shaft
(figure 6) and place the assembled Plunger onto
the end of the Plunger Shaft (figure 7).
Figure 1
Fast gear shaft
Slow gear shaft
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 282588 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 282588 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info