Manual Hendi 272602 (page 8 of 144) (English, German, Dutch, French, Italian, Polish)

742600

Zoom out

Zoom in

1/144

To light the patio heater

• The pilot should be lit and the knob set to PILOT.

• Press the knob 3mm and turn anti-clockwise to

HIGH.

• When mesh glows lit, turn knob clockwise from

HIGH to LOW as needed.

Note: The burner may be noisy when initially

turned on. To eliminate excessive noise from the

burner, turn the control knob to the pilot position.

Then, turn the knob to the level of heat desired.

Re-lighting

Note: For your safety, Control Knob cannot be turned OFF without first depressing Control Knob in PILOT

position and then rotating it to OFF.

• Turn Control Knob to OFF.

• Wait at least 5 minutes, to let gas dissipate, be-

fore attempting to re-light pilot.

• Repeat the “Lighting” steps

To extinguish

• Hold knob depressed & turn the knob clockwise

to ‘OFF’

• Close the valve of the gas cylinder or the regula-

tor after use.

• Allow this appliance to cool before moving.

Note: After use, some discoloration of the emitter

screen is normal.

Leak testing

NEVER USE A NAKED FLAME TO CHECK FOR LEAKS.

NEVER LEAK TEST WHILE SMOKING

The gas connections on this appliance are leak

tested at the factory prior to shipment.

This appliance needs to be periodically checked

for leaks and an immediate check is required if the

smell of gas is detected.

• Make a soap solution using 1 part of liquid

dish-washing soap to 3 parts water. The soap

solution can be applied with a soap bottle, brush,

or rag to the leak tested points shown in the ﬁg-

ure above.

• The valve of the gas cylinder should be in the OFF

position at this point of the leak test. Once the

soapy solution is applied to the gas connections,

the valve of the gas cylinder needs to be turned to

the ON position.

• Soap bubbles will begin to form in the soapy solu-

tion if a leak is present.

• In case of a leak, turn off the gas supply. Tighten

any leaking ﬁttings, then turn the gas supply on

and recheck.

Leak Test Point 1 2

Gas requirements

• The pressure regulator and hose assembly to be

used must conform to local standard codes.

• Never use a gas cylinder with a damaged body,

valve, collar, or foot ring.

• A dented or rusty gas tank may be hazardous and

should be checked out by a gas supplier.

• Never connect this appliance to an unregulated

gas source.

• When the appliance is not in use, turn the gas

cylinder OFF.

• Always perform a leak test on gas connections

whenever a cylinder is connected. If bubbles form

in the leak test solution, do not use. Never use a

ﬂame to test for leaks.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 272602 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 272602 Manual

Product: