Manual Hendi 232965 (page 7 of 120) (English, German, Dutch, French, Italian, Polish)

742476

Zoom out

Zoom in

1/120

• When running for the first time, it should run

without load for 2 hours to ensure the refriger-

ation system is working normally. Only when the

temperature within the appliance is reduced with-

in the indicated scope can the food be put into the

appliance.

• Don’t put too much food in the appliance to pre-

vent instantaneous high load. The food shall not

block the air outlet and air inlet. Nor shall it be

close to side glass. Otherwise it will lead to con-

densation.

• To keep the taste of the food, please have the

equipment running 24 hours a day.

• During the frosting process, the temperature of

the appliance may rise slightly. When the frosting

end, it will return to normal.

ATTENTION: During transport, avoid skew the unit

from the vertical by an angle greater than 30 °, If

necessary, wait approximately 3-4 hours before

running, until the oil flows to the unit. Otherwise,

the condensing unit may be damaged.

6.2. PACKAGING

Upon receipt of the appliance, check the packaging

for any transport damage.

Carefully remove the external cardboard, loosen the

bolts fixing the appliance to the pallet (if present -

they secure the appliance from movement during

transport), put the appliance aside and remove the

protection film from the outer housing.

By recycling of packaging materials such as plas-

tics, steel, cardboard and wood, we significantly

contribute to saving raw materials and waste re-

duction.

Comply with local regulations regarding the meth-

od and place of disposal of the appliance packaging

materials.

6.3. LEVELLING

To ensure correct functioning it is important to level

the appliance. Correct levelling allows for reduction

of vibration generated by the unit in operation.

Thoroughly check the levelling with the use of a

spirit level.

CAUTION!

To ensure proper functioning of the cooling/

freezing appliance, strictly follow the instructions

below:

• Do not put the appliance in a place exposed to di-

rect sunlight and near appliances emitting radi-

ation, such as: heat lamps, stoves, radiators etc.

• Avoid integrating or building over of the appliance.

• Do not place any objects on the top of the appli-

ance housing where the refrigerating unit is lo-

cated.

• Do not place the appliance in a room with relative-

ly high humidity (water can liquify on the housing).

• Do not place the appliance in narrow recesses (if

there is no air circulation, the appliance will not

function properly).

• Do not cover ventilation openings located on the

housing.

• Do not place the appliances back to back (they will

not operate properly).

Ensure that the room where the appliance is placed

is properly ventilated, also outside of working

hours; it is crucial for proper operation of the re-

frigerating unit.

6.4. MINIMUM DISTANCE FROM WALLS

In order to ensure proper operation of the appli-

ance, during the installation remember to ensure

minimum distance from walls in accordance with

the drawings below. Remember to ensure the ap-

propriate amount of space in front of the appliance

as well - it is necessary for easy opening of the cool-

ing/freezing chamber doors.

600 600 600 600 600

500

FRONT SIDE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 232965 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 9,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 232965 Manual

Product: